Hand Tools
Traditional tools, sharpening, restoration, usage techniques.
Related: Hand Tools archive
Topic list
-
TopicStatisticsLast post
-
Death Knell of Woodcentral? 2 3 4
by TomD 6/8/12, 6:07 PM
80 Replies · 400 ViewsLast post 7/2/12, 12:39 PM by david weaver -
by eliot feldman 7/1/12, 8:29 PM
2 Replies · 67 ViewsLast post 7/2/12, 11:22 AM by eliot d -
Looking for drawing bow improvements....
by roger lance 6/23/12, 3:39 PM
14 Replies · 62 ViewsLast post 7/2/12, 3:06 AM by TomD -
by Ellis Walentine 6/21/12, 9:49 PM
2 Replies · 56 ViewsLast post 7/1/12, 8:25 PM by eliot d -
Might as well start the LV PM-V11 Thread 2 3 4
by david weaver 6/26/12, 6:16 PM
90 Replies · 908 ViewsLast post 7/1/12, 4:04 PM by Bill Tindall, E.TN. -
by Bruce Mack 7/1/12, 2:12 PM
1 Reply · 49 ViewsLast post 7/1/12, 2:53 PM by John in NM -
Experimenting with chip breakers 2 3
by Derek Cohen (in Perth, Australia) 5/21/12, 8:44 AM
54 Replies · 490 ViewsLast post 6/30/12, 8:31 PM by bridger -
by Stephen Shepherd 6/29/12, 5:13 PM
6 Replies · 93 ViewsLast post 6/30/12, 3:35 PM by Bruce, a MN Galoot -
by John Veerkamp 6/30/12, 1:27 PM
2 Replies · 46 ViewsLast post 6/30/12, 2:11 PM by david weaver -
by Moses Yoder 6/28/12, 12:37 PM
9 Replies · 86 ViewsLast post 6/30/12, 5:42 AM by Ellis Walentine -
Discussion of Lee Valley new steel PM V11 2
by Bill Tindall, E.TN. 6/27/12, 11:34 PM
27 Replies · 175 ViewsLast post 6/30/12, 3:15 AM by TomD -
Revisiting various abrasion(dulling) mechanisms 2 3
by Bill Tindall, E.TN. 6/19/12, 9:51 PM
51 Replies · 367 ViewsLast post 6/29/12, 5:35 PM by Mark Hennebury -
Shoot board plane clearence angle?
by craigd 6/25/12, 8:31 PM
6 Replies · 92 ViewsLast post 6/29/12, 8:31 AM by craigd -
Anyone have comments on super blue steel? 2 3 4
by david weaver 6/20/12, 3:34 PM
76 Replies · 433 ViewsLast post 6/28/12, 9:42 PM by CStan -
by TomD 6/26/12, 7:54 PM
16 Replies · 107 ViewsLast post 6/28/12, 5:19 PM by Roy -
Tom - Did You Ever Find a 80mm Kanna?
by david weaver 6/20/12, 7:03 PM
2 Replies · 59 ViewsLast post 6/27/12, 8:08 PM by david weaver -
by Bill Tindall, E.TN. 6/24/12, 12:15 AM
20 Replies · 96 ViewsLast post 6/27/12, 3:01 AM by Bob Hackett -
Recommend lever cap replacement
by CJ in MPLS 6/25/12, 11:25 PM
7 Replies · 112 ViewsLast post 6/27/12, 1:45 AM by TomD -
Tuesday Night Hand Tool Chat - In the Heat
by Stephen Shepherd 6/26/12, 3:22 PM
0 Replies · 49 ViewsLast post 6/26/12, 3:22 PM by Stephen Shepherd -
by Denis Chenard in Ottawa 6/23/12, 3:50 AM
4 Replies · 42 ViewsLast post 6/26/12, 2:49 PM by Bob Hackett -
by Kees 6/22/12, 8:35 PM
37 Replies · 283 ViewsLast post 6/26/12, 7:27 AM by Kees -
Awesome video on mortising *LINK* 2
by James Watriss 6/22/12, 6:48 PM
37 Replies · 140 ViewsLast post 6/25/12, 11:54 PM by TomD -
Question re Chipbreaker Discussion 2
by Jerry Murrey 6/21/12, 3:43 PM
31 Replies · 242 ViewsLast post 6/24/12, 3:49 AM by TomD -
Back to Woodworking- Card Table
by Bill Tindall, E.TN. 6/21/12, 12:16 PM
13 Replies · 53 ViewsLast post 6/23/12, 12:14 PM by Mark Hennebury -
by Stephen Shepherd 6/21/12, 7:14 PM
4 Replies · 82 ViewsLast post 6/23/12, 12:04 AM by Gary Roberts -
by Tony - Memphis 6/22/12, 3:34 PM
5 Replies · 90 ViewsLast post 6/22/12, 7:52 PM by Paul M. -
by steve mackay 6/20/12, 9:38 PM
3 Replies · 49 ViewsLast post 6/22/12, 1:54 AM by Bill Tindall, E.TN. -
by roninkokomo 6/19/12, 2:51 PM
21 Replies · 70 ViewsLast post 6/21/12, 7:28 PM by Wiley Horne - S. CA -
Sad what this site has come to 2
by Rocky 6/15/12, 4:46 AM
25 Replies · 122 ViewsLast post 6/21/12, 10:29 AM by CStan -
by Jack Guzman from Maine 6/18/12, 12:08 AM
20 Replies · 85 ViewsLast post 6/20/12, 8:11 PM by Jack Guzman from Maine



