Hand Tools
Traditional tools, sharpening, restoration, usage techniques.
Related: Hand Tools archive
Topic list
-
TopicStatisticsLast post
-
by David Weaver 9/2/19, 7:19 PM
0 Replies · 67 ViewsLast post 9/2/19, 7:19 PM by David Weaver -
by Bill Tindall, E.TN. 8/30/19, 7:46 PM
8 Replies · 178 ViewsLast post 9/2/19, 7:14 PM by Brian Holcombe -
by Bob Rush 9/1/19, 12:54 AM
3 Replies · 76 ViewsLast post 9/2/19, 5:44 PM by David Weaver -
CITES Musical Instrument Relief - Padauk Listing
by david weaver 8/30/19, 4:46 PM
0 Replies · 77 ViewsLast post 8/30/19, 4:46 PM by david weaver -
by David Weaver 8/19/19, 12:10 PM
44 Replies · 287 ViewsLast post 8/29/19, 10:59 AM by Jim Matthews -
by Bill Tindall, E.TN. 8/28/19, 12:11 AM
3 Replies · 74 ViewsLast post 8/29/19, 12:04 AM by Jim Matthews -
by Bill Tindall, E.TN. 8/27/19, 6:54 PM
2 Replies · 61 ViewsLast post 8/27/19, 7:50 PM by Wiley Horne -
"It's a waste of time to make stanley irons"
by David Weaver 8/25/19, 12:11 PM
20 Replies · 123 ViewsLast post 8/27/19, 3:10 PM by david weaver -
Hand tool work in the state parks? *LINK*
by Bill Houghton 8/26/19, 3:48 PM
4 Replies · 100 ViewsLast post 8/27/19, 11:51 AM by david weaver -
by Denny 8/26/19, 1:05 AM
3 Replies · 74 ViewsLast post 8/26/19, 2:06 PM by Denny -
Question for CBN grinding wheel users?
by E Phillip Smith 8/21/19, 2:33 PM
15 Replies · 342 ViewsLast post 8/22/19, 6:00 AM by Derek Cohen (in Perth, Australia) -
by Bill Tindall, E.TN. 8/20/19, 9:14 PM
2 Replies · 73 ViewsLast post 8/22/19, 1:21 AM by Bill Tindall, E.TN. -
by Mark Mandell 8/21/19, 3:23 PM
4 Replies · 100 ViewsLast post 8/21/19, 11:23 PM by Mark Mandell -
Tormek: getting old wheel off? 2 3
by Wiley Horne 8/16/19, 3:14 AM
51 Replies · 450 ViewsLast post 8/20/19, 11:48 PM by E Phillip Smith -
by david weaver 8/19/19, 5:46 PM
9 Replies · 168 ViewsLast post 8/20/19, 5:56 PM by david weaver -
Removing the waste from half blind sockets *LINK*
by Derek Cohen (in Perth, Australia) 8/19/19, 6:27 AM
1 Reply · 121 ViewsLast post 8/19/19, 6:36 PM by Jonathan Elliott -
by Joe shelton 8/18/19, 1:56 PM
6 Replies · 120 ViewsLast post 8/18/19, 10:37 PM by Joe shelton -
One more wildcard- Washita and 1 micron-768 feet
by David Weaver 8/15/19, 2:40 AM
8 Replies · 120 ViewsLast post 8/18/19, 5:25 PM by David Weaver -
Recommendations for grinder/wheel 2
by Wiley Horne 8/12/19, 5:42 PM
31 Replies · 300 ViewsLast post 8/16/19, 6:10 AM by bridger berdel -
by David Weaver 8/14/19, 3:21 AM
51 Replies · 693 ViewsLast post 8/15/19, 5:23 PM by Jonathan Elliott -
LN's desperate attempt to get more of my $$$
by Kent B 8/14/19, 6:21 PM
13 Replies · 142 ViewsLast post 8/15/19, 3:55 PM by david weaver -
edge pictures from end grain testing
by David Weaver 8/15/19, 1:40 AM
3 Replies · 86 ViewsLast post 8/15/19, 1:52 AM by David Weaver -
60 Replies · 405 ViewsLast post 8/15/19, 1:31 AM by Wiley Horne
-
by David Weaver 8/11/19, 12:28 PM
14 Replies · 121 ViewsLast post 8/14/19, 7:33 PM by david weaver -
Kato and Kawai on "wedge angle"
by Bill Tindall, E.TN. 8/13/19, 8:27 PM
10 Replies · 142 ViewsLast post 8/14/19, 3:05 PM by david weaver -
Old films - Mode of action of a planer
by John Schtroumpf 8/14/19, 12:21 PM
1 Reply · 52 ViewsLast post 8/14/19, 1:34 PM by Bill Tindall, E.TN. -
Duration by Abrasive 2 - 30 degrees
by David Weaver 8/13/19, 4:09 AM
17 Replies · 105 ViewsLast post 8/14/19, 12:57 PM by david weaver -
Bill had the chinese iron analyzed
by david weaver 8/12/19, 6:08 PM
3 Replies · 94 ViewsLast post 8/14/19, 11:34 AM by David Weaver -
Duration by Abrasive - 2 - 35 degree
by David Weaver 8/12/19, 3:43 AM
8 Replies · 127 ViewsLast post 8/13/19, 1:10 PM by david weaver -
by Kees 8/11/19, 1:12 PM
20 Replies · 156 ViewsLast post 8/12/19, 11:31 PM by Clint Searl



