Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Hand plane to the rescue

Posts

Hand plane to the rescue

#1

Hand plane to the rescue

Bill Tindall, E.Tn.

I am installing the crown molding to the top of the corner cupboard (see post Main Board). Shown is the top rail of the top unit. I have a bad enough time installing crown anyway but this situation had me flummoxed for a bit. There was a hump where the knot is (knot will be hidden under crown) and the stiles are not exactly in the same plane as the rail. The crown stick teetered on the knot hump and the miters didn't align at the ends.

The solution was to plane the whole affair flat. Now I see why you serious planers speak of planing fatigue. It takes some push to shave a knot.


(top of corner cupboard view)

I certainly had not anticipated needing to plane this gnarly piece of wood. Grain is going every which a way. The wonderful invention of the cap iron led to no tear out, Yea! Even the knot planed smooth.

Yet, to quote the Lee Valley literature,

"A cap iron serves to stiffen a plane blade, helping to damp vibration and reduce the potential for blade chatter. "

Why do they deny the true function of this device?

Re: Hand plane to the rescue

#2

Clint Searl

Farrier's rasp...

Clint Searl

...could have made short work of it.

Re: Hand plane to the rescue

#3

Re: Hand plane to the rescue

Mark Nowicki

For knots, I use my Stanley #8C.

It barely hesitates.

Re: Hand plane to the rescue

#4

Crown went on ok

Bill Tindall, E.Tn.


Crown installation went ok. Miters are always stressful for me.

As it stands the shellac wash coat has been applied. Remaining- Sand, stain, first varnish coat, sand, second varnish coat, sand, top coat

Re: Hand plane to the rescue

#5

“OK” doesn’t quite get it, Bill

Wiley Horne

It’s fabulous! The miter is flawless to these eyes. And the molding is not store bought, either—I recall your making it yourself (tablesaw, right?).

Really like how the figure carries around the corner into the return.

It’s great.

Wiley

Re: Hand plane to the rescue

#6

Re: “OK” doesn’t quite get it, Bill

Bill Tindall, E.Tn.

I don't use any "store bought" moldings, ever. I find that I can scrape a molding surprisingly fast. I never need more than 4'.

Getting the hump and other irregularities out of the place the molding was to lay, and then fitting it, took several hours. Nobody would even pay me for what I make. Too slow. But, I never do enough of the same thing to ever get fast. There were endless 1sts on this corner cupboard.

There is a show at a nearby museum featuring Period and contemporary furniture from the area. In colonial times there were numerous cabinet makers in Greenville, TN and Abingdon, VA, the end of the Crooked Road that connected to Philly and then on to New Orleans by boat on Holston, TN and Miss. River.

There are some attractive and creative contemporary pieces displayed among the Period pieces. But I recoiled at "soft close" drawer hardware on a desk that had no need for a hardware assisted drawer. Kitchen hardware has NO place in fine furniture. I don't understand why I find it often in the product of young cabinet makers. Who is teaching this stuff is acceptable? It will eventually break or rust and then how can it be fixed 75 years from now? Thankfully I don't see it in similar furniture from the Krenov school.

Re: Hand plane to the rescue

#7

Re: Farrier's rasp...

William Duffield

I wouldn't use a farrier's rasp, because it is way too coarse, and the bottom inch of the board with the knot will be exposed in the finished case. In fact, I would be reluctant to use one of my hand stitched cabinetmaker's rasps because I would still be afraid one or more errant tooth scratches might be left exposed, if I wasn't careful enough.

I think I like Mark's idea better, or at least go a couple steps up to a #7 (or #607).

Re: Hand plane to the rescue

#8

Re: Crown went on ok

David Weaver

That's beyond OK. It's divine. If it doesn't open at all with seasonal movement, then it's worth of teaching to others, even more than it is already.

I see the mention of purchased moulding, and don't have any experience with it, but it's such a rewarding part of the process that I'd trade 3 parts making mouldings vs. 1 part trying to find it and then being offended by the price or the amount of work you have to do to actually finish scrape it.

Re: Hand plane to the rescue

#9

Re: “OK” doesn’t quite get it, Bill

Brian Holcombe

Nice work, Bill.