General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
Interesting new wood product: Ligneah *LINK*
by Leo Cuellar 6/11/16, 1:07 AM
0 Replies · 35 ViewsLast post 6/11/16, 1:07 AM by Leo Cuellar -
perfect TS sled fence, no measurement
by eliot feldman 6/8/16, 3:47 PM
6 Replies · 72 ViewsLast post 6/10/16, 11:59 PM by eliot feldman -
by Keith Newton 6/9/16, 3:11 AM
6 Replies · 49 ViewsLast post 6/10/16, 3:38 AM by Matt Robinette -
by Jesse Cloud 6/6/16, 3:39 AM
10 Replies · 87 ViewsLast post 6/9/16, 5:18 PM by Jesse Cloud -
by Derek Cohen (in Perth, Australia) 6/6/16, 3:25 PM
19 Replies · 91 ViewsLast post 6/9/16, 12:01 PM by Don Orr -
So I bought a Klingspor belt for Performax....
by Barry Irby 6/4/16, 7:50 PM
3 Replies · 33 ViewsLast post 6/8/16, 3:17 PM by Grant Smith -
Hand Tool Chat tonight 9:30 PM EDT
by Bob Entwisle in NJ 6/7/16, 11:32 AM
2 Replies · 39 ViewsLast post 6/8/16, 2:28 AM by Bob Entwisle -
OT Finally off the dot - small gloat -long
by Gary Smyth 6/6/16, 5:28 PM
4 Replies · 46 ViewsLast post 6/7/16, 2:18 PM by William Duffield -
Perfromax thickness sander crowned wheel
by john lucas 6/6/16, 1:15 PM
11 Replies · 66 ViewsLast post 6/7/16, 10:46 AM by john lucas -
WC Weekend Accomplishments....
by Dennis E Peacock 6/6/16, 12:59 PM
2 Replies · 25 ViewsLast post 6/7/16, 12:22 AM by Matt Robinette -
by Mark Mandell 6/2/16, 7:48 PM
33 Replies · 101 ViewsLast post 6/7/16, 12:17 AM by John in NM -
by eliot feldman 6/5/16, 6:38 PM
5 Replies · 41 ViewsLast post 6/6/16, 2:27 PM by eliot feldman -
Roadshow - Tambour expanding table
by Craig Daymon 6/5/16, 6:15 PM
2 Replies · 41 ViewsLast post 6/6/16, 4:26 AM by Dick Coers -
by Peter Rad 6/5/16, 7:40 PM
6 Replies · 33 ViewsLast post 6/6/16, 3:53 AM by Yonak -
I gotta get one of these. *LINK*
by Keith Newton 6/2/16, 8:37 PM
17 Replies · 42 ViewsLast post 6/5/16, 8:27 PM by TomD -
Whats your favorite Dovetail jig?
by Bart Goldberg 6/3/16, 4:33 PM
12 Replies · 150 ViewsLast post 6/4/16, 7:01 PM by Mike Van Pelt -
by Steven Kirincich 6/3/16, 7:55 PM
2 Replies · 25 ViewsLast post 6/4/16, 6:48 PM by Mike Van Pelt -
Donation becomes a sucking discount
by Tom Dunlap 6/4/16, 5:34 AM
0 Replies · 47 ViewsLast post 6/4/16, 5:34 AM by Tom Dunlap -
by Barry Irby 6/2/16, 3:49 PM
9 Replies · 43 ViewsLast post 6/4/16, 1:53 AM by John K Jordan -
Winding sandpaper on drumsander question
by Barry Irby 6/1/16, 12:06 PM
3 Replies · 25 ViewsLast post 6/2/16, 10:19 PM by John K Jordan -
by Bruce, a MN Galoot 5/27/16, 8:07 PM
17 Replies · 64 ViewsLast post 6/2/16, 9:58 PM by Jay Lombardo -
Two speed tablesaw replacement motor
by Bill Mackey 6/1/16, 1:42 PM
5 Replies · 25 ViewsLast post 6/2/16, 3:48 PM by Bill Mackey -
Test for Silicone Contamination?
by don stephan 6/2/16, 12:26 AM
6 Replies · 77 ViewsLast post 6/2/16, 2:50 PM by Ellis Walentine -
by Bruce, a MN Galoot 6/1/16, 2:16 PM
10 Replies · 57 ViewsLast post 6/2/16, 11:19 AM by Bruce, a MN Galoot -
by AZ 5/29/16, 3:55 AM
8 Replies · 28 ViewsLast post 6/2/16, 3:44 AM by AZ -
by Barry Irby 6/1/16, 11:49 AM
9 Replies · 30 ViewsLast post 6/2/16, 3:11 AM by North of the Border -
Old 15" Porter Cable disk sander
by Keith Newton 5/31/16, 11:00 PM
5 Replies · 36 ViewsLast post 6/1/16, 6:32 PM by Robin Corell in Atascadero, CA -
Stabilizing bark on table edges
by Henry Justus 5/30/16, 4:35 PM
3 Replies · 36 ViewsLast post 5/31/16, 11:36 PM by Keith Newton -
by Barry Irby 5/30/16, 3:24 PM
8 Replies · 74 ViewsLast post 5/31/16, 11:08 PM by Steve jenkins -
QSWO better left to power tools
by Matt Robinette 5/28/16, 3:26 AM
10 Replies · 84 ViewsLast post 5/31/16, 8:01 PM by Bob Lang



