Bookmark Accounts
Home Articles Forums Gallery Marketplace Videos
Support WoodCentral when buying things you need
New here? How did you find us?

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

General Woodworking

Cross-cutting topics, techniques, and questions that don’t fit a specialty.

ACTIONS | Post new topic

Topic list

  1. Micro Fence Edge Guide

    by scott bonder 9/18/01, 3:34 PM

    0 Replies · 335 Views
    Last post 9/18/01, 3:34 PM by scott bonder

  2. Rockler router table extension

    by Eric Mickelson 9/17/01, 6:53 PM

    2 Replies · 271 Views
    Last post 9/18/01, 1:10 PM by Floyd Knapp

  3. Do I really need a spiral bit?

    by MikeC 9/17/01, 7:58 PM

    5 Replies · 343 Views
    Last post 9/18/01, 2:59 AM by Carol, the Router Lady, Ramona, CA

  4. Sterling chest corner splitting

    by Richard Schump 9/17/01, 11:40 PM

    1 Reply · 202 Views
    Last post 9/18/01, 2:21 AM by Lee Grindinger

  5. Wood Prices

    by Phil B. 9/18/01, 12:08 AM

    1 Reply · 174 Views
    Last post 9/18/01, 1:48 AM by Hoa Dinh

  6. New Proposed Parking Lot

    by besterJ 9/17/01, 8:58 PM

    1 Reply · 194 Views
    Last post 9/18/01, 12:49 AM by Larry Williams

  7. Homemade Walnut Stain

    by Ed DeLauter 9/17/01, 4:24 AM

    2 Replies · 566 Views
    Last post 9/17/01, 11:55 PM by Clint Searl

  8. Melimine Chery Joint

    by Lynn Porter 9/17/01, 1:36 AM

    5 Replies · 285 Views
    Last post 9/17/01, 10:14 PM by NickB

  9. I jheard from Eddie Pacheco...

    by Dave Anderson Chester,NH 9/17/01, 6:36 PM

    1 Reply · 210 Views
    Last post 9/17/01, 7:49 PM by MgtExec

  10. e-mail address?

    by Barney Loden 9/17/01, 4:30 PM

    2 Replies · 299 Views
    Last post 9/17/01, 5:26 PM by Greg Davis

  11. Milling Walnut from Acreage

    by Greg Davis 9/17/01, 5:13 PM

    0 Replies · 274 Views
    Last post 9/17/01, 5:13 PM by Greg Davis

  12. My Wife, Rescue worker on the front lines.

    by Chris Knob 9/17/01, 1:23 PM

    3 Replies · 205 Views
    Last post 9/17/01, 2:45 PM by Bob Hutchins, Belton, TX

  13. Re: Motor spin Direction

    by Larry Clinton 9/17/01, 4:16 AM

    0 Replies · 270 Views
    Last post 9/17/01, 4:16 AM by Larry Clinton

  14. If you get bored...

    by Dan Donaldson 9/17/01, 2:43 AM

    0 Replies · 254 Views
    Last post 9/17/01, 2:43 AM by Dan Donaldson

  15. Predator Tools

    by jd webb 9/17/01, 12:31 AM

    1 Reply · 185 Views
    Last post 9/17/01, 1:24 AM by Mike in the Garden State

  16. Re: I debated with myself over this.

    by Gary Camp (Bend Or.) 9/16/01, 8:44 PM

    3 Replies · 208 Views
    Last post 9/17/01, 12:22 AM by Robert R Clough

  17. W & M Highboy???

    by Joe Burke 9/16/01, 1:44 PM

    1 Reply · 204 Views
    Last post 9/16/01, 11:46 PM by Stephen Shepherd

  18. Re: I wish I could do more

    by Richard Herman (Dick) 9/16/01, 10:05 PM

    0 Replies · 369 Views
    Last post 9/16/01, 10:05 PM by Richard Herman (Dick)

  19. Agree with Ellis

    by Dave Heinlein 9/15/01, 8:36 PM

    0 Replies · 257 Views
    Last post 9/15/01, 8:36 PM by Dave Heinlein

  20. I've been in 50 or more pattern shops in 25 years

    by MgtExec 9/15/01, 7:03 PM

    0 Replies · 333 Views
    Last post 9/15/01, 7:03 PM by MgtExec
ACTIONS | Post new topic
× Share

Share on

X / Twitter Facebook LinkedIn
✉ Email this page