General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
Samantha's dresser 9- fixing a problem
by Bill Tindall, E.TN. 2/10/14, 9:49 PM
0 Replies · 22 ViewsLast post 2/10/14, 9:49 PM by Bill Tindall, E.TN. -
by Joe 2/9/14, 4:32 AM
12 Replies · 39 ViewsLast post 2/10/14, 7:21 PM by Joe -
WC Weekend Accomplishments....
by Dennis E Peacock 2/10/14, 1:20 PM
1 Reply · 28 ViewsLast post 2/10/14, 4:40 PM by Larry in NW Ohio -
by Tom 2/8/14, 9:02 PM
4 Replies · 80 ViewsLast post 2/10/14, 12:52 AM by Alan -
by Larry 2/9/14, 12:43 AM
4 Replies · 27 ViewsLast post 2/10/14, 12:39 AM by Larry -
advice needed on phase converter
by McKay 2/9/14, 1:41 AM
3 Replies · 43 ViewsLast post 2/9/14, 7:30 PM by Thomas S Stockton -
by Larry in NW Ohio 2/7/14, 3:19 PM
5 Replies · 69 ViewsLast post 2/9/14, 2:31 PM by Larry Clinton At Frankfort, (Central) Indiana -
by John Foster 2/8/14, 4:14 PM
2 Replies · 37 ViewsLast post 2/9/14, 1:36 PM by John Foster -
by Bill Tindall, E.TN. 2/6/14, 3:11 PM
3 Replies · 38 ViewsLast post 2/8/14, 10:30 PM by Tom in Toronto -
by Ken Hart 2/8/14, 4:34 PM
0 Replies · 22 ViewsLast post 2/8/14, 4:34 PM by Ken Hart -
Tuesday Night Hand Tool Chat - Static Electricity
by Stephen Shepherd 2/4/14, 4:41 PM
2 Replies · 26 ViewsLast post 2/8/14, 1:48 PM by Larry Clinton At Frankfort, (Central) Indiana -
surface planning marks on walnut
by Jim Coats 2/4/14, 10:15 AM
16 Replies · 55 ViewsLast post 2/8/14, 3:45 AM by William Duffield, on the Cohansey -
by Stuart Hough 2/3/14, 1:26 AM
25 Replies · 64 ViewsLast post 2/8/14, 12:54 AM by John in NM -
by gary clarke 2/7/14, 1:13 AM
8 Replies · 49 ViewsLast post 2/7/14, 4:21 PM by Barry Irby -
by Kevin in CO 2/6/14, 5:53 PM
6 Replies · 23 ViewsLast post 2/7/14, 5:02 AM by Tom -
by Bill Tindall, E.TN. 2/6/14, 3:38 PM
8 Replies · 176 ViewsLast post 2/7/14, 12:20 AM by Dave's Not Here -
by Ellis Walentine 2/5/14, 8:34 PM
7 Replies · 57 ViewsLast post 2/7/14, 12:19 AM by Keith Newton -
Crystal Varnish Repair on floor
by Bill from Montreal 2/6/14, 6:29 PM
3 Replies · 30 ViewsLast post 2/6/14, 10:58 PM by Dick Coers -
Ever have used mnrl sprts that just won't settle?
by Tim Greif - West of Chicago 2/5/14, 11:48 PM
4 Replies · 24 ViewsLast post 2/6/14, 2:16 PM by Tim Greif -
Half round table. Testing my form. 2
by Joe 2/3/14, 3:22 AM
31 Replies · 47 ViewsLast post 2/6/14, 12:57 PM by Barry Irby -
Performax 16-32 drum alignment
by Jim in N. Va 2/1/14, 8:01 PM
16 Replies · 74 ViewsLast post 2/6/14, 12:55 PM by Barry Irby -
Moisture loss and regain and sprung joints 2
by Bill Tindall, E.TN. 2/4/14, 1:14 AM
25 Replies · 96 ViewsLast post 2/6/14, 8:37 AM by Sgian Dubh -
Finally bought a small compressor. *LINK*
by Keith Newton 2/5/14, 2:51 AM
17 Replies · 146 ViewsLast post 2/6/14, 1:23 AM by Keith Newton -
by Tom 2/4/14, 10:03 PM
6 Replies · 19 ViewsLast post 2/5/14, 6:12 PM by Dick Coers -
by Tom 1/31/14, 9:54 PM
12 Replies · 27 ViewsLast post 2/5/14, 1:43 PM by Tom -
WC Weekend Accomplishments....
by Dennis E Peacock 2/3/14, 1:50 PM
11 Replies · 23 ViewsLast post 2/5/14, 12:31 AM by Bill Tindall, E.TN. -
by Yonak 2/4/14, 4:52 AM
11 Replies · 51 ViewsLast post 2/4/14, 11:20 PM by paul in AZ -
correct router w/top adjustment capabilities
by Garrett Aston 2/4/14, 5:15 PM
2 Replies · 31 ViewsLast post 2/4/14, 8:18 PM by Hoa in Alameda -
by Ellis Walentine 2/1/14, 7:59 PM
3 Replies · 26 ViewsLast post 2/3/14, 7:03 PM by Howard Norman -
by Barry Irby 2/1/14, 4:14 PM
6 Replies · 29 ViewsLast post 2/3/14, 4:15 PM by Jason Roehl in Lafayette, IN



