Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Looking for help

Posts

Looking for help

#1

Looking for help

Kevin in CO

Long time fan, first post. I'm looking for a way to wire a small indicator lamp to show that power tools are powered on. My father is an avid woodworker, but at 87, has lost his hearing. His eyesight is good but he has several times left saws powered on because he doesn't hear. If I could mount a small LED to come on when tablesaw or bandsaw is on, it could help avert a real disaster. Any suggestions or devices already on the market?

Re: Looking for help

#2

Re: Looking for help *LINK*

Tony - Memphis

I use a device from Sears to indicate when my dust collector is on. I have a lamp with a red bulb plugged into it. Works great.

Tony


Craftsman AutoSwitch

Re: Looking for help

#3

PS

Tony - Memphis

Something that turns on a dust collector automatically could work too. There was an article in FWW? about how to build a box with a current sensor (just a coil) that fires up a relay via a transistor I think and thus does the same function as the Sears box. My DC is 120. There might be something out there for 220 if needed.

I bought an inexpensive wall mounted fixture at Lowes or HD that looks like and industrial caged fixture. I wired an extension cord to it and plugged it into the Sears autoswitch. I use a red light bulb so it is easy to see even in my peripheral.

Hats off to your dad to still be making sawdust at 87! I hope I am too!

Tony

Re: Looking for help

#4

Re: Looking for help

Dick Coers

I would suggest a master switch on the breaker box to kill all power to the shop when he leaves. A hot melt gun left on might be one example that may have bad results if left on for a couple of days.

Re: Looking for help

#5

More info would help.

Keith Newton

If you could give the brand and model #, we might could tell you how to just wire it into the switch.

On both of the TSs in my shop, I have a little pigtail wired into the switch that I plug a shop vacuum into, so whenever I turn the saw on, the vac comes on too.

Now, having said that, before anyone starts piling on, I knew ahead of time, and wired circuits larger than the saw needed, and also came off between the contact points and the motor overload protection. But for the very low amp draw of an LED, you don't need to worry about that.

Re: Looking for help

#6

Maybe a solution

Lee Schierer in McKean, PA

You could replace all the plugs on his tools with power indicating plugs. Leviton makes several. Then he would need to remember to unplug them.

Or you could convert his outlets to switched outlets with switches that have indicators showing the circuit is on.

Lee

Re: Looking for help

#7

Re: Looking for help

Tom

I have used lighter power version of this on small fixed tools like grinders. It is kill switch that LV sells. There are certain things where the bad times keep on rolling when the scarf hits the fan. My best example was when I tried to use a spade bit in a drill press. I powered it up, and it instantly started to wobble. I hit the floor, but it would have been great if the bit rather than making like an aircraft prop and then snapping off, would have just powered down. I bought mine at LV:

http://www.harborfreight.com/momentary-power-foot-switch-96619.html

LV has these privacy mats, and they are like regular door mats, but when you step off your session is over on the computer. Something like that for a table saw, so you foot wasn't cranked at a bad angle would be great. If you walk off it turns off, but you still have a magnetic switch to use. A mag switch is another thing to install, they reset to off if the power goes out, or a cord gets pulled. So if there was such a mat, you could walk off, it would kill the saw, but the saw wouldn't turn on when you stood on the mat again.

Another thing that is a big issue is fluro lights that can sync with the moving blade and appear turned off when they are in fact moving. Make sure if he can't hear the difference that there is a flicker free source of light in the shop. I don't know if LEDs are flicker free, but regular light bulbs are. Dimmers can do weird things on flicker.