General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
Rub for TX smoked brisket..needed
by Bill Tindall, E.TN. 1/13/13, 12:47 AM
5 Replies · 43 ViewsLast post 1/15/13, 3:32 PM by Derek Arita -
by Harry Walls 1/14/13, 2:13 AM
13 Replies · 55 ViewsLast post 1/15/13, 1:44 AM by Phil -
by Mike Schwing from Md 1/10/13, 5:09 PM
8 Replies · 36 ViewsLast post 1/15/13, 12:26 AM by Larry Clinton At Frankfort, (Central) Indiana -
Jointers - Helical or Straight Knife Cutterhead?
by Barry 1/12/13, 7:58 PM
8 Replies · 22 ViewsLast post 1/14/13, 8:55 PM by William Duffield -
Semi-OT But It Definitely Is WOOD *LINK*
by John McGaw 1/13/13, 9:59 PM
1 Reply · 12 ViewsLast post 1/14/13, 8:01 PM by Thomas Skaggs -
by Jim B 1/13/13, 2:12 AM
11 Replies · 33 ViewsLast post 1/14/13, 6:26 PM by Jim Breeden -
by Stuart Hough 1/13/13, 3:22 AM
3 Replies · 16 ViewsLast post 1/14/13, 5:48 AM by Bob -
by Larry in nw ohio 1/13/13, 10:45 PM
1 Reply · 13 ViewsLast post 1/13/13, 10:48 PM by Jason Roehl in Lafayette, IN -
by tom 1/13/13, 9:13 PM
0 Replies · 21 ViewsLast post 1/13/13, 9:13 PM by tom -
OT Is this Offensive or is it me?
by Barry Irby 1/13/13, 1:28 AM
7 Replies · 34 ViewsLast post 1/13/13, 1:54 PM by Barry Irby -
by Mark 1/12/13, 4:27 PM
4 Replies · 17 ViewsLast post 1/13/13, 1:35 PM by Bill Tindall, E.TN. -
by tom 1/11/13, 11:01 PM
17 Replies · 70 ViewsLast post 1/13/13, 6:28 AM by TomD -
by Ron Goldman 1/13/13, 3:19 AM
0 Replies · 20 ViewsLast post 1/13/13, 3:19 AM by Ron Goldman -
by Butch...Mn 1/12/13, 6:08 PM
3 Replies · 15 ViewsLast post 1/13/13, 12:56 AM by Jim DeLaney, Austintown, Ohio -
by Derek Arita 1/12/13, 6:34 PM
3 Replies · 10 ViewsLast post 1/13/13, 12:29 AM by Alan Young -
Going to make a corner cabinet - question
by Joe 1/11/13, 2:09 PM
8 Replies · 28 ViewsLast post 1/12/13, 1:29 PM by Joe -
Not 100% OT: Name this mechanism
by Henry Higginbotham 1/11/13, 3:56 PM
11 Replies · 24 ViewsLast post 1/12/13, 11:46 AM by Al Stokka -
by Steve Kirincich 1/11/13, 7:25 PM
2 Replies · 29 ViewsLast post 1/11/13, 10:20 PM by paul in AZ -
by Doug Ridley 1/10/13, 7:57 PM
8 Replies · 51 ViewsLast post 1/11/13, 5:10 PM by Doug Ridley -
by John Lucas 1/10/13, 6:34 PM
10 Replies · 32 ViewsLast post 1/11/13, 2:51 PM by Terry Quiram -
by Tom Rex in TX 1/10/13, 1:57 PM
7 Replies · 35 ViewsLast post 1/11/13, 8:20 AM by TomD -
by Derek Arita 1/7/13, 3:58 PM
9 Replies · 13 ViewsLast post 1/10/13, 11:43 PM by Derek Arita -
by Jerry Nicholson 1/9/13, 8:34 PM
13 Replies · 51 ViewsLast post 1/10/13, 7:42 PM by Bill Tindall, E.TN. -
by james jacomb 1/10/13, 4:21 PM
0 Replies · 21 ViewsLast post 1/10/13, 4:21 PM by james jacomb -
OT - Large caulk tube sources?
by JL 1/9/13, 2:20 PM
14 Replies · 125 ViewsLast post 1/10/13, 3:56 PM by james jacomb -
Planning hard-to-reach Plywood
by Ron Milan 1/9/13, 4:15 PM
9 Replies · 56 ViewsLast post 1/10/13, 2:39 PM by Jim DeLaney, Austintown, Ohio -
by John Lucas 1/8/13, 8:10 PM
16 Replies · 91 ViewsLast post 1/10/13, 2:21 AM by Bob Entwisle -
mating wood along an irregular curve
by eliot feldman 1/7/13, 5:53 PM
18 Replies · 93 ViewsLast post 1/9/13, 9:53 PM by Mark Hennebury -
OT-If you need a morning laugh *LINK*
by John Lucas 1/7/13, 4:17 PM
6 Replies · 20 ViewsLast post 1/9/13, 7:59 PM by Howard Norman -
WC Weekend Accomplishments.....
by Dennis E Peacock 1/7/13, 1:54 PM
5 Replies · 13 ViewsLast post 1/9/13, 7:03 PM by George



