Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Going to make a corner cabinet - question

Posts

Going to make a corner cabinet - question

#1

Going to make a corner cabinet - question

Joe in a Cleveland suburb

Hello.

I am going to make a corner cabinet/tv stand.

I've made a cardboard mock up (ugly cell phone image below). It's going to be about 36" wide, 24" high, and 15" deep. It's going to have a poplar face frame and a couple doors. There will be a shelf in the middle. The case will be plywood. I'm going to use biscuits and/or pocket screws. It's going to get painted and put in a room that gets little use. A tv will sit on top.

This isn't intended to be an heirloom piece... I want to make it quickly and cheaply. I plan to even use big box birch plywood.

My question: since it's so small, is there any reason why I can't use 1/2" birch ply? I'm aware of the caveats using big box ply (warpage, voids, etc.).

Thanks!


Re: Going to make a corner cabinet - question

#2

Re: Going to make a corner cabinet - question

Bill Tindall, E.Tn.

I find 3/4 easier to work with, less wiggly. I bought some 3/4 birch from Home Depot and it warped into potato chip configuration. Checked moisture and it was 18%!!!.

Re: Going to make a corner cabinet - question

#3

Re: Going to make a corner cabinet - question

Ralph Lipeles

I agree with Bill. If you want to stick with 1/2", I would use 3/4" by 3/4" glued and screwed cleats to reinforce all inside corners

Re: Going to make a corner cabinet - question

#4

Re: Going to make a corner cabinet - question

NickinMass

I built a corner cabinet last year (built-in, paint grade) for our dining room. 3/4 birch ply and poplar face frames.

I'm with Bill - the 1/2" seems too wiggly. Also, not much meat for pocket screws.

Re: Going to make a corner cabinet - question

#5

Re: Going to make a corner cabinet - question

Dave Bair

Might want to make it wider; with falling prices, there may be a 40"+ HD TV in your future.

Re: Going to make a corner cabinet - question

#6

Agree

Nat Robison

I have a 32" TV that's about 34" wide but has to sit back from the front edge of its cabinet about 6-7" because of the TV's base.

Your dimensions might limit you to a TV no bigger than 32". I was planning a similar cabinet (still might) and figured the front edge needed to be about 48-51" to accomodate a 40' flat screen

My first big project about 6-7 years ago was a TV armoire to accomodate (at the time) a 27" CRT TV. This was a year or two before flat screens hit the scene and approached affordability. It's still in use but I definitely would have changed the dimensions had I been able to foresee the flat screen dimensions that are typical now.

Re: Going to make a corner cabinet - question

#7

Ellis Walentine

Short answer: No, but...

Ellis Walentine

There's no reason you can't use 1/2" plywood, *IF* you engineer it properly. That means glue blocks as someone suggested, and some method of bracing and/or stiffening the construction to overcome the relative flimsiness of the lighter-gauge plywood.

All that extra work will quickly overcome any cost savings by using the 1/2" material. With 3/4" ply, you can do mitered biscuit joints and be done with it.

My 2¢,

Ellis

Re: Going to make a corner cabinet - question

#8

You might wish to go to the sagulator (Honest)

Gary Smyth

You will plug in your dimensions and it will calculate if it will deflect. If you use solid wood it will be stronger. Give them a look.

Re: Going to make a corner cabinet - question

#9

Thanks all!  Good advice as always.  3/4" it will