Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Planning hard-to-reach Plywood

Posts

Planning hard-to-reach Plywood

#1

Planning hard-to-reach Plywood

Ron Milan

PROBLEM: Need to plane off 1/8” from ¾” plywood sheet in a constrained situation.

SITUATION: We have a triangular kitchen table that has three cherry wood sides that are sandwiched around ¾” plywood making a triangle table. The top of the three border sides are ¼” higher than the plywood. One quarter (¼) inch tiles have been inlaid in the triangle eating table. The ¼” titles have been removed and a 3/8” title is now to be inlaid. (Because of the construction, the screws, the glue, and the fit, the cherry wood cannot be disassembled to insert a 5/8” plywood sheet.)

PLEASE ADVISE: Can you advise on how to take off 1/8” of the plywood in the middle space, the tight confining corners, and around the 1/8” cherry wood edges without nicking? Can an amateur do this?

Thank you

Re: Planning hard-to-reach Plywood

#2

Re: Planning hard-to-reach Plywood

Mark Hennebury

I think that the easiest way would be this:

use a router.

use a straight cut bit fairly large diameter say 1" but not to long.

If you have a plunge router: ( you can do it without a plunge router, you just have to be careful making the plunge)

Starting in the middle of you table, plunge the bit down 1/8"

the carefully make ever greater circles until you are out near the edges, then get as close to the lip as you can. You can put a 1/8" support block on your base once you make the circle big enough if you need the support.

Then for the edges, i would probably use a fence and straightedge of some sort.

Re: Planning hard-to-reach Plywood

#3

Bob

Re: Planning hard-to-reach Plywood

Bob

Are you removing the face of the plywood? or is it solid wood? Sorry I cant picture what you are doing.

Re: Planning hard-to-reach Plywood

#4

Re: Planning hard-to-reach Plywood

Jason Waters

That's what I would do. or something very similiar. for the edge, a straight board and pattern bit.

Jason

Re: Planning hard-to-reach Plywood

#5

Re: Planning hard-to-reach Plywood

Thomas Skaggs, Foothills of Mount Level

A router with a large straight or spiral bit can do it. You will need a support for the base of the router that is at least 1/4" thick. Otherwise your base will butt into the cherry edges. Carefully remove 1/8" of depth everywhere but stop short of removing all the way to the cherry borders. Then remove the rest with a chisel...to make sure you don't damage those cherry edges.

Another option would be to not remove, but to add 1/4" to the top of the cherry edges. Maybe like a 1/4" banding....maybe of a contrasting wood? Might be a cool detail and would save you a lot of work?

Tom

Re: Planning hard-to-reach Plywood

#6

Shim the table face?

Robby Wright in San Marcos, CA

If you are removing the old tile, exposing the table surface, wouldn't it be easier to apply a 1/8" layer of plywood or hardwood to the surface of the table? This would bring the top of the tile up to the top of the edging if I understand everything correctly. This would be much lower risk than trying to trim the edging.

Re: Planning hard-to-reach Plywood

#7

Kneale Brownson

Re: Planning hard-to-reach Plywood

Kneale Brownson

I'm with Tom: I'd add something to the edge pieces rather than try to reduce the whole surface.

Re: Planning hard-to-reach Plywood

#8

Re: Shim the table face?

Ron Milan

Hi

I should have enclosed a picture to better highlight the problem. After removing the inlaid 1/4" titles from a triangular top table, there remains the cherry borders on the table 1/4" higher than the now de-tiled plywood. My wife wants to re-insert another color tile that is 3/8" or 1/8" deeper than the removed tiles. (Planning 1/8 inch off means the new inlaid tile is level with the cherry borders. ) Thus, how to I remove 1/8" in the middle, along the edges without nicking the cherry, and in the tight triangular corners.

Thanks

Re: Planning hard-to-reach Plywood

#9

Re: Planning hard-to-reach Plywood

Ron Milan

Thomas

I wish I would have ask your advice before my wife already purchased the 3/8" tile.

Re: Planning hard-to-reach Plywood

#10

Jim DeLaney, Austintown, Ohio

Re: Planning hard-to-reach Plywood

Jim DeLaney, Austintown, Ohio

You don't say how big the table top is, but if it were me, I'd just remove the cherry edging and either reinstall it an eighth of an inch higher (assuming it now overlaps the bottom of the plywood a bit), or just make and install new edging.

It'd be a heck of a lot less work to do it that way, and the small amount of cherry needed for new edging wouldn't be that expensive. If you've got the tools and skills needed for trimming the ply down, you're certainly capable of handling the edging.