Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Supertune your Tablesaw

Posts

Supertune your Tablesaw

#1

Supertune your Tablesaw

Jim B

I have a General 350 TS purchased in 2004. When I first purchased the saw I checked the blade alignment at 90 degrees (0.003) and at 45 degree (0.012). I was not happy with the 45 degree angle but I figured it was good enough. I am in the process of making an Arts and Crafts Limbert table which calls for tapered 45 degree cuts...I figured now was the time to tune up my TS...I rechecked the alignment and it was now at 0.005 at 90 and 0.015 at 45. I tried to realign the blade but noticed that one bolt was hanging my ability to line things up. So I removed the top and elongated one of the holes that connects the table top to the cabinet. This made a huge difference. I could now align the top without too much problem...of course I had to sneak up on the settings tweaking each bolt a little at a time but got it set up to 0.002...cool...now on to the 45 degree angle. I rechecked and now it was out by 0.010 not awful but not good enough.

I remember reading an article in American Woodworker Magazine about setting up your TS blade at 45 degrees so I plunked in my fairly new DVD with all of the AWW magazines from 1985-2010 and found the article in AWW #43 February 1995. I followed along and used the author, Tom Borroughs, calculations to figure how thick the shims should be and where they should be placed. Anyway the calculation came to adding a 0.024 thick shim between the two rear mounting bolts and table...put them in...redid the alignment at 90 degrees to within 0.015 and then measured at 45 degrees...0.002...acceptable in my book!

Jim

Re: Supertune your Tablesaw

#2

Re: Supertune your Tablesaw

Jim B

Oops...should read "redid the alignment at 90 degrees to within 0.0015....."

Re: Supertune your Tablesaw

#3

Re: Supertune your Tablesaw *LINK*

Bob Entwisle in NJ

Here's a link to the article in AWW for anyone who's interested.

Bob in NJ


Supertune your Tablesaw

Re: Supertune your Tablesaw

#4

Re: Supertune your Tablesaw

John Lucas

Years ago I had the same dilema on my Powermatic Contractors saw. It just never would cut clean at any tilting angle. I had read and read and and adjusted my table saw till I was blue in the face. Then I found the article you are talking about. After adjusting my saw (and it's a bear to do that on a contractors saw) it cut like a dream. So I went back through all of my magazines and I have more than 20 years of virtually every woodworking magazine out there. That was the only article on aligning a table saw that mentions that very critical adjustment. Amazing isn't it.

It made me wonder how many other things might be missing from articles on how to tune up other machines.

Re: Supertune your Tablesaw

#5

Re: Supertune your Tablesaw

Clementine

I have the same table saw, and really like it. What did you use to check the angle? I've been looking at the Wixley Digital Angle Gauge from Rockler. BTW, I got a 3/8" link belt from Belt Palace (General used a 3/8" belt instead of 1/2"), and it made a really big difference, along with a Freud thin kerf ripping blade. Now I just need to work on my skill level.

Re: Supertune your Tablesaw

#6

Re: Supertune your Tablesaw

Jim B

Bob,

Good find! I remember you could view the old AW magazines on the Google book site!

Thanks for posting!

Jim

Re: Supertune your Tablesaw

#7

Ellis Walentine

Guess who edited that article?


Re: Supertune your Tablesaw

#8

Re: Guess who edited that article?

Dave Bair

Is it anyone we know from here at WC?

Re: Supertune your Tablesaw

#9

Ellis Walentine

Guilty 


Re: Supertune your Tablesaw

#10

Re: Supertune your Tablesaw

Jim Breeden

Bob - I clicked on the link and nothing happened. What ?

Wait ! I just googled and found the answer - thanks for the info !

Re: Supertune your Tablesaw

#11

Re: Supertune your Tablesaw

Terry Alexander

Stoopid question. Can you tell me how to print the article?

Tks

Terry Alexander in West Texas

Re: Supertune your Tablesaw

#12

Re: Supertune your Tablesaw  "link"  *LINK*


http://americanwoodworker.com/blogs/tools/archive/2009