General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Nathan 12/14/07, 6:15 PM
8 Replies · 34 ViewsLast post 12/15/07, 4:25 PM by George@Colonel's Workshop-Havertown, PA -
Can I use a Forrest WWII for MDF?
by Mike Farinella 12/14/07, 3:51 AM
9 Replies · 61 ViewsLast post 12/15/07, 3:42 PM by knotscott -
by Paul T 12/14/07, 11:46 PM
8 Replies · 55 ViewsLast post 12/15/07, 1:46 PM by NickB -
Router Raizer question and my new Freud router
by David Charters (Durham, NC) 12/15/07, 2:14 AM
1 Reply · 24 ViewsLast post 12/15/07, 4:18 AM by Dick Coers------WebKitFormBoundaryqFOmq51H3saAc+aC -
looking for 12/4 cherry 36" long for legs
by Wayne Carson "TX" 12/13/07, 2:07 PM
6 Replies · 40 ViewsLast post 12/14/07, 11:22 PM by Steve Jenkins, McKinney, TX. -
by Terry Alexander 12/14/07, 1:57 PM
12 Replies · 50 ViewsLast post 12/14/07, 11:15 PM by Ralph Turney -
Honing carbide circular saw blades ? ?
by Pete in Holland, MI 12/14/07, 6:38 PM
3 Replies · 28 ViewsLast post 12/14/07, 9:40 PM by steve antonucci -
A Little Christmas Entertainment... *LINK*
by Jason Roehl in Lafayette, IN 12/13/07, 10:29 PM
6 Replies · 39 ViewsLast post 12/14/07, 9:24 PM by Don in Central Illinois -
by Rich Schneider 12/14/07, 8:06 PM
0 Replies · 23 ViewsLast post 12/14/07, 8:06 PM by Rich Schneider -
by Howard 12/12/07, 7:14 PM
9 Replies · 58 ViewsLast post 12/14/07, 7:04 PM by Howard -
by Mark Mandell 12/13/07, 9:49 PM
14 Replies · 42 ViewsLast post 12/14/07, 2:32 PM by Mark Mandell - Gone Round In Jersey -
by Jeffrey D. ROse 12/13/07, 4:54 PM
4 Replies · 31 ViewsLast post 12/14/07, 3:35 AM by Jeffrey D. Rose -
I waited way too long to install this thing *LINK*
by Mike Schwing from Md. 12/13/07, 2:25 PM
8 Replies · 40 ViewsLast post 12/14/07, 2:51 AM by Joanne Adler in Pt. Pleasant, PA -
OT - New 3D model maker *LINK*
by Joe Pack 12/13/07, 9:22 PM
3 Replies · 32 ViewsLast post 12/14/07, 1:11 AM by ScottS -
by jeff 12/13/07, 1:24 PM
8 Replies · 60 ViewsLast post 12/14/07, 1:05 AM by Rick Christopherson -
by Garrett in Victoria 12/13/07, 6:39 PM
1 Reply · 25 ViewsLast post 12/14/07, 1:02 AM by steve mackay -
Benefit auction, turning blanks.
by Gary Evans Tallassee, TN 12/12/07, 11:58 PM
1 Reply · 27 ViewsLast post 12/14/07, 12:05 AM by Gary Evans Tallassee, TN -
by Mike Schwing from Maryland 12/12/07, 2:27 PM
11 Replies · 36 ViewsLast post 12/13/07, 10:14 PM by Barry Irby -
It's Nice to Have Good Neighbors!
by Robert R Clough - Thorncraft 12/13/07, 1:21 AM
6 Replies · 34 ViewsLast post 12/13/07, 6:55 PM by Don in Northern Arizona -
by Ellis Walentine 12/10/07, 3:40 PM
3 Replies · 32 ViewsLast post 12/13/07, 5:08 PM by Mark in B'ham -
problem with thickness planer 2
by Cody Lewis 12/10/07, 8:01 PM
25 Replies · 607 ViewsLast post 12/13/07, 4:42 PM by Jay St. Peter - Southern, MD -
by Virgil Johnson 12/11/07, 5:33 PM
9 Replies · 57 ViewsLast post 12/13/07, 4:38 PM by Jay St. Peter - Southern, MD -
Question - Jet/Performax 16-32 Plus Drum Sander
by Ralph Turney 12/12/07, 8:38 PM
6 Replies · 77 ViewsLast post 12/13/07, 4:29 PM by Ralph Turney -
by ernie miller 12/12/07, 11:51 PM
4 Replies · 33 ViewsLast post 12/13/07, 4:02 PM by Jerry Nicholson -
OT -A Different Christmas Poem
by Ron Hildreth 12/12/07, 5:47 PM
1 Reply · 20 ViewsLast post 12/13/07, 2:36 PM by waroland -
Website make-over... Opinions... *LINK*
by HC Sakman 12/10/07, 10:04 AM
17 Replies · 64 ViewsLast post 12/13/07, 2:29 PM by JohnKJordan in East TN -
by Barry Irby 12/12/07, 8:41 PM
5 Replies · 28 ViewsLast post 12/13/07, 1:21 PM by Bill White -
by John Halstead 12/13/07, 4:50 AM
2 Replies · 30 ViewsLast post 12/13/07, 1:06 PM by Barry Irby -
by Wayne 12/10/07, 11:49 PM
5 Replies · 35 ViewsLast post 12/13/07, 12:49 PM by Barry Irby -
by lee beeden 12/11/07, 12:55 AM
7 Replies · 30 ViewsLast post 12/13/07, 12:31 PM by Barry Irby



