Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

I waited way too long to install this thing *LINK*

Posts

I waited way too long to install this thing *LINK*

#1

I waited way too long to install this thing *LINK*

Mike Schwing from Md.

>The MJ splitter from Microjig, that is.


I've had it in my drawer for sometime. Yesterday afternoon I finally put it in before ripping a whole stack of mahogany.

I knew it would help keep pinches from occuring but I never considered just how great it would be at keeping the saved pieces tight against the fence. I'm not the greatest in the world at holding work tight against a fence as my fence is on the right side and I'm a lefty, I am always wishing my fence was on the left as I naturally push in that direction. After ripping several boards yesterday I couldn't quite figure out why everything was staying so nice and tight against the fence as it exited the saw blade, then I realized that it was that little splitter. Much more accurate now!

GRRReat little gadget, adds both safety AND accuracy.

Also available from Lee Valley.


MJ Splitter

Re: I waited way too long to install this thing *LINK*

#2

Re: I waited way too long to install this thing

George@Colonel's Workshop-Havertown, PA

>Good Morning Mike,

It looks like I could use that little sucker to good advantage. I use zero clearance inserts on my Jet table saw. These are home made, mostly of white oak or maple. I wonder if the splitter "would" work well in wood or would be prone to tear out of the mounting holes. What is your opinion?

George

Re: I waited way too long to install this thing *LINK*

#3

Re: I waited way too long to install this thing

Mike Schwing from Md.

>George, from my limited experience I think it would work fine. The included drill bit makes for a tight fit. I had to ream them out a little bit to fit in my phenolic zero clearance insert. The manual states that an extremely "bindy" piece of wood might lift the insert out and that you should watch for that - they call it a safety feature.

Two little inserts are included each with different clearance tolerances. For example, in one orientation the insert moves a little more to the keeper side of the kerf, the other to the waste side. Clever.

Re: I waited way too long to install this thing *LINK*

#4

Try this, George

Neal in San Jose

>On some of the plywood zero clearance inserts I made for my old saw, I cut a slot right behind the blade and glued in a small scrap of 1/8 ply to do the same thing. High quality thin plywood is available at any hobby shop and some craft stores. I usually had to lightly sand the ply "splitter" to keep it from dragging excessively, and I always waxed 'em. Obviously, they can't be higher than the blade on non-thru cuts, but they were very easy to "adjust".

Re: I waited way too long to install this thing *LINK*

#5

Re: I waited way too long to install this thing

Larry Clinton At Frankfort (Central)., Indiana

>George, I have the Microjig splitter in my "homemade" inserts for my Unisaw. I made several inserts at the same time from Baltic Birch then laminated some scrap formica on top. I have pulled it out a few times - saved pinching the blade. I did finally destroy one splitter - I really like the little units. Wish the replacements weren't so expensive.

Re: I waited way too long to install this thing *LINK*

#6

Re: Try this, George

Ross

>A piece of 1/8" drill rod or cold rolled rod works just as well. You can buy 3 feet of it for a couple of bucks at the hardware store or borg.

Re: I waited way too long to install this thing *LINK*

#7

Re: I'm waiting to get the right size in the mail

Brian in Brighton

>They make 2 sizes based on thin kerf/regular blade. I told the guy at the Denver show when I bought my Grrrrrrrrippperrrrs that I had a thin kerf and he put the regular kerf in thr bag. Noticed it after the show had left town. My wife is mailing it back and they offered to replace it with the right one. I need to see if she ever mailed it yet.

I like it because it's simple, slick and easy to remove.

Brian in Brighton

Re: I waited way too long to install this thing *LINK*

#8

Re: I waited way too long to install this thing

Nick Tuzzolino

>George: Yes, they work well in wood. I have used two of them (one for standard kerf, and one for thin kerf) in home made zero clearance inserts for at least two years. Like 'em a lot.

Nick

Re: I waited way too long to install this thing *LINK*

#9

I've been using one for a while, too

Joanne Adler in Pt. Pleasant, PA

>I make my zero clearance inserts out of mdf and I've put the little splitter in and out a few times without a problem. Usually I just change the zci to one without the splitter, and leave it in there.