Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Question - Jet/Performax 16-32 Plus Drum Sander

Posts

Question - Jet/Performax 16-32 Plus Drum Sander

#1

Question - Jet/Performax 16-32 Plus Drum Sander

Ralph Turney

>Hey all,

I just picked this up from Rockler the other night and only had time to assemble it and begin to get it ready for sanding...I never go much past the assembly stage though. The manual says that the conveyor belt was shipped "over tensioned", but no where does it say what proper tension should be, or how you can tell if it's proper. Very irritating, it just says to tension it not to tight and not to loose. Well heck, if I know what proper was it would be easy!!! I already loosened it and tried to make it work, but the belt would start to move off track and it seemed that no amount of adjusting would bring it back to center.

Can anyone describe what proper tension is and how I can tell it I have achieved it?

Thanks!

Re: Question - Jet/Performax 16-32 Plus Drum Sander

#2

Re: Question - Jet/Performax 16-32 Plus Drum Sande

Jesse Cloud

>My understanding is that the tension is right when the belt tracks straight, e.g., doesn't travel to the right or left.

Re: Question - Jet/Performax 16-32 Plus Drum Sander

#3

Re: Question - Jet/Performax 16-32 Plus Drum Sande

Ralph Turney

>Like I said, I didn't get a lot of time to spend on it, but is seemed that if the belt was in anyway snug, the belt would drift off the the left. The only way to get it to track straight was to have the belt SO loose that it had lumps in it. Wouldn't the amount of tension on the belt, unless of course it is too tight (again, what's too tight) and the tracking be more or less unrelated???

Re: Question - Jet/Performax 16-32 Plus Drum Sander

#4

Re: Question - Jet/Performax 16-32 Plus Drum Sande

Kirk (KC) Constable

>Welcome to the club...

The belt obviously has to be tight enough to not slip... but also has to track more or less correctly. In my case, less... or not at all. I've given up trying to adjust it after hours upon hours of trying, and just skooch it back to the other extreme periodically.

Re: Question - Jet/Performax 16-32 Plus Drum Sander

#5

Re: Question - Jet/Performax 16-32 Plus Drum Sande

Ralph Turney

>Welcome to the club...Thanks!

The belt obviously has to be tight enough to not slip... but also has to track more or less correctly. In my case, less... or not at all. I've given up trying to adjust it after hours upon hours of trying, and just skooch it back to the other extreme periodically.

So this is just something I'll have to live with huh...well that sucks. It just seems that the belt needs to be so loose that it might hit the drum is it's set at a half an inch. I'll play with it more later.

Thanks for the help!

Ralph

Re: Question - Jet/Performax 16-32 Plus Drum Sander

#6

Land another question for Ralph and others?

Barry Irby

>I bought my Performax used and replaced the belt. AS I recall, I just tightened the belt until it was snug and smooth. Ran it a while to get the "stretch" out and snugged it again.

Not so good on the tracking either. Mine runs over near the motor side, but it doesn't seem to hurt anything, so I leave it alone. The old belt crashed into one side of the other and tore itself to pieces.

My question is about the pressure rollers. Mine seem to have little more downward pressure than their own weight. I just recently noticed I can lift them up easily with my fingers from underneath. I never noticed how much pressure they had before. I suspect a spring or something is gone. Do yours press down firmly or are they pretty loose?

Re: Question - Jet/Performax 16-32 Plus Drum Sander

#7

Re: Land another question for Ralph and others? *LINK*

Ralph Turney

>I'll try to remember to go down to the garage after my ride tonight and check that out, but I've been reading the manual...I know, I know, but since I can't play with the tool I've been reading the thing hoping to glean some info for when I can play with it. It sure looks like the rollers are much the same as on a planer, except they don't feed, but they do exert downward force on the wood as it's going through. Maybe you can down load the manual from Jet and look on page 19 and 20. It describes how to adjust them and some pictures of the area and the parts to work on.

Here's the link to the manual if you don't already have it.

Ralph


http://content.jettools.com/manuals/man_629004K.pd