Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Router bearings on table?

Posts

Router bearings on table?

#1

Router bearings on table?

Nathan

>I'm relatively inexperienced so please forgive my ignorance. I'm gearing up (shop- and tool-wise as well as psychologically) to do our new kitchen, including the carcasses and doors, plus I've got to do a bunch of round-over molding in pine to go in three bedrooms upstairs that recently got pine flooring installed (by yours truly). Anyway, the upshot of this is I'm finally going to start using the router table I built last year.

I've been researching router bits and I can understand why a bearing is useful for freehand routing with a template or along the edge of a workpiece. I can also see its use in the router table without a fence. What I don't understand is what use a bearing bit could have when used in the table with a fence to guide the work. Is there any?

Re: Router bearings on table?

#2

Re: Router bearings on table?

calvin in Irmo, SC

>No advantage if using the fence to control depth of cut. However, bearing on bit in router table does not cause any problem in my experience, and makes the bit more useful for other applications: i. e. handheld router use or not straight-line routing.

Re: Router bearings on table?

#3

Re: Router bearings on table?

Robert Henderson

>I agree, but would add that fences have been known to slip.

Been there, done that, bought the t-shirt.

Re: Router bearings on table?

#4

Re: Router bearings on table?

George@Colonel's Workshop-Havertown, PA

>Good Afternoon Nathan,

The bearing is used in conjunction with the fence to support the work as cutter does its job. It also serves to limit the depth of the cut to no more than the cutter's design profile. I use bearings on every bit used in the router table. For raising panels, the fence can accommodate stock subject to multiple shallow passes to achieve partial profiles. The bearing serves as a limit for the final, full profile pass.

George

Re: Router bearings on table?

#5

Re: Router bearings on table?

Hank Knight

>In addition to what the Colonel said, the bearing facilitates setting the fence/depth of cut for the final pass. Hold a straight edge across the cutter opening in the fence, adjust the fence so the bit bearing just contacts the straight edge and lock the fence down.

Re: Router bearings on table?

#6

Re: Router bearings on table?

Barry Irby

>I agree with all of the above. And I would add:

I have had the fence slip, really, I could not possible have set it wrong, really.

I have also had the bearing fall off during a job. That got a little dicey, so be sure the Allen screw or nut is secure. (mine were cheap Chinese bits that I bought to use sort of on a one time basis)

I also have a bit where the bearing wore out and is no longer concentric with the bit. Not good.

So you can use bits with bearings with a fence and you can also use bits without a bearing. It give you versatility. With the fence, you can take light cuts or you can use just a part of the bit, not easy with a bearing alone. An example of how a fence could be useful is lets say you have a 3/8" radius bit and you want to run a bull nose on the edge of a 3/4 board. The first pass is easy, but when you flip to the other side to run the other edge, you will discover you just cut away the surface the bearing would have run on and the two cuts won't line up.

I don't have a fancy fence, usually just a scrap clamped to the table. I have my router sunk into the wing of my TS and thought using the TS fence for the router would be a great idea. Not so much. It seems that every time I get it tweaked just like I want it I find I need the fence for the TS.

So, yes a fence would be useful. I would also suggest that you look at having a tall fence also so that you can stand the piece on edge if that gets you the profile you want.

Re: Router bearings on table?

#7

Thanks to all

Nathan

>Thanks to all who responded. I wasn't aware of the bearing's support function when aligned with the fence.

Yes, I have a high fence for my router table but I only recently got a featherboard for it and I don't have the fence grooved yet to take the featherboard mounting strip.

Re: Router bearings on table?

#8

Re: Router bearings on table?

del schisler

>check out these web sites The best http://www.routerforums.com/ http://www.routerworkshop.com/ their i is also http://www.thewoodworkingchannel.com/ I check these all the time del

Re: Router bearings on table?

#9

Re: Thanks to all

George@Colonel's Workshop-Havertown, PA

>Good Morning Nathan,

Use C-clamps to attach the featherboards until you manage grooves in the fence. Truth be known, I used C-clamps and for a long time prior to having a groved fence system.

George