General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Ken Platt (Granby, CT) 8/2/08, 4:49 PM
9 Replies · 49 ViewsLast post 8/6/08, 2:40 AM by Ken Platt (Granby, CT) -
Sliding Dovetails on a PC 4212
by A300 Pilot 8/2/08, 7:48 PM
4 Replies · 25 ViewsLast post 8/5/08, 11:29 PM by Ken Garlock, Collin County Texas -
by Rusty Miller 8/5/08, 5:34 PM
1 Reply · 9 ViewsLast post 8/5/08, 11:05 PM by Ken Garlock, Collin County Texas -
OT Working with plastic lumber????
by Barry Irby 8/5/08, 1:37 PM
5 Replies · 20 ViewsLast post 8/5/08, 7:42 PM by George Koch -
by Robin Corell in Atascadero CA 8/2/08, 6:22 PM
18 Replies · 53 ViewsLast post 8/5/08, 6:51 PM by Dan Mitchell -
by David Yoho 8/4/08, 12:18 PM
9 Replies · 24 ViewsLast post 8/5/08, 6:17 PM by Marv....... Northern California Lake Co. -
by galen V 8/4/08, 4:33 AM
5 Replies · 22 ViewsLast post 8/5/08, 5:16 PM by galen V -
by Rick Haverstock 8/5/08, 2:18 AM
2 Replies · 12 ViewsLast post 8/5/08, 3:59 PM by George -
by Stephen Shepherd in the State of Deseret 8/5/08, 10:18 AM
0 Replies · 17 ViewsLast post 8/5/08, 10:18 AM by Stephen Shepherd in the State of Deseret -
Very basic electrical question
by Clint Searl, at the base of Haycock Mtn 8/4/08, 11:08 AM
9 Replies · 34 ViewsLast post 8/5/08, 6:58 AM by John Ballance -
by DP 8/4/08, 3:47 PM
4 Replies · 12 ViewsLast post 8/5/08, 3:16 AM by Jason Roehl in Lafayette, IN -
Homemade Remote Control for D/C
by Jim Vest 8/4/08, 1:47 AM
14 Replies · 93 ViewsLast post 8/5/08, 2:24 AM by Garrett in Victoria -
When do you decide to resaw (and how thick)?
by JL 8/3/08, 8:52 PM
8 Replies · 59 ViewsLast post 8/4/08, 11:32 PM by JL -
Domed Trunk, progress and questions
by Bill Tindall, E.TN. 8/3/08, 5:10 PM
6 Replies · 40 ViewsLast post 8/4/08, 5:35 PM by Bill Tindall, E.TN -
jointer safety, shorter pieces
by John K Jordan 8/2/08, 5:47 PM
9 Replies · 52 ViewsLast post 8/4/08, 5:35 PM by Keith Newton, LR, Arkansas------WebKitFormBoundary -
What's a reasonable price to pay for 10/4 cherry?
by JL 7/31/08, 11:19 PM
7 Replies · 29 ViewsLast post 8/4/08, 4:37 PM by Miles -
Message to Andrew F in Australia
by Ray Carson - Lawrenceville, NJ 8/4/08, 4:06 PM
0 Replies · 14 ViewsLast post 8/4/08, 4:06 PM by Ray Carson - Lawrenceville, NJ -
by Tony - Memphis 8/3/08, 5:19 PM
12 Replies · 47 ViewsLast post 8/4/08, 1:57 PM by Tony - Memphis -
Painting a finished table top and chairs
by Rick Van Schoick 7/30/08, 5:16 PM
10 Replies · 27 ViewsLast post 8/4/08, 1:40 PM by pecker -
by Jon Martin 8/2/08, 1:59 AM
5 Replies · 18 ViewsLast post 8/4/08, 1:16 PM by Lena -
True story - difference btw owner and sales staff
by North of the Border 8/2/08, 5:05 AM
16 Replies · 136 ViewsLast post 8/4/08, 11:22 AM by Brent in Montreal -
by Larry in NW Ohio 8/2/08, 11:59 PM
7 Replies · 14 ViewsLast post 8/4/08, 4:36 AM by Fred Davis -
by Dean Lapinel 8/2/08, 7:28 PM
9 Replies · 40 ViewsLast post 8/4/08, 2:11 AM by Dean Lapinel -
by Sawman 8/3/08, 8:57 PM
2 Replies · 8 ViewsLast post 8/4/08, 2:07 AM by Mark Nowicki -
by Ray Newman 8/3/08, 10:50 PM
2 Replies · 14 ViewsLast post 8/4/08, 12:50 AM by Bill Tindall, E.TN -
by Bill Pfahl in Virginia 8/3/08, 11:05 PM
1 Reply · 10 ViewsLast post 8/3/08, 11:08 PM by Bill Pfahl in Virginia -
by Joseph Mulherin, Sr 7/31/08, 5:00 PM
14 Replies · 71 ViewsLast post 8/3/08, 10:22 PM by John K Jordan -
by scottinphoenix 8/3/08, 5:42 PM
0 Replies · 30 ViewsLast post 8/3/08, 5:42 PM by scottinphoenix -
by Larry in NW Ohio 7/30/08, 2:03 PM
9 Replies · 32 ViewsLast post 8/3/08, 3:41 PM by Chuck in ND -
I need a really aggressive drill Bit......
by Barry Irby 8/1/08, 10:44 PM
8 Replies · 21 ViewsLast post 8/3/08, 2:13 PM by Barry Irby



