Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

How to make "pillowed" pegs?

Posts

How to make "pillowed" pegs?

#1

How to make "pillowed" pegs?

Ken Platt (Granby, CT)

>Folks -

I'm in the final stages of making a Green & Greene style bed, and am up to making the decorative pegs. FWW had an article in #191 about making pegged joints, and they had a little sidebar with various profiles for the pegs. One of those was what looks like a softened-edges and flattened top look and is apparently termed "pillowed".

I was wondering if anyone has made pegs in this style, and how one gets the pillowed look. Best I can figure, it starts out as a pyramidal profile, then is sanded. Freehand sanding, though, usually ends up messy for me, so I'm wondering if it's just that one needs better eye-hand than I've got, or if there is some way that this is machined to give consistent results.

Thanks for all suggestions.

Ken

Re: How to make "pillowed" pegs?

#2

Re: How to make "pillowed" pegs? *LINK*

Thomas S Stockton

>Ken,

I did a hole response on how to make pegs and Eddie Pacheco added a nice pic of a cool peg holder he made to pillow them. But the way you want to do them is the easiest I've found.

I also e-mailed the tutorial to the articles section but it hasn't shown up there yet

Tom


ebony peg tutorial

Re: How to make "pillowed" pegs?

#3

Re: How to make "pillowed" pegs?

Ken Platt (Granby, CT)

>Thanks, Tom. That is a great tutorial. I had been thinking that I needed to undercut the bottom of the pyramid/bevel so that I wouldn't have any visible gaps between the peg and the sides of the hole. You didn't mention that, so I'm guessing that your "tight fit" was good enough?

I think your way will save me a lot of time, and I do have a mortiser that I can use for most of the holes, and of course the chisel itself by hand for the ones that I cannot get onto the machine.

Ken

BTW, an issue of Wood magazine (#154, p.12) had a little jig in it similar to yours for sanding. However, they had guide blocks kinda reversed, so that there was an open "V" between the two, apex at the sanding disk, with a small gap the width of the chamfer between the two guides. The workpiece went alongside the one guide, and the other limited how far it could go, so that you got a consistent bevel. Probably useful for the coordination-challenged like me, otherwise I'll spend a lot of time getting even bevels.

Re: How to make "pillowed" pegs?

#4

Re: How to make "pillowed" pegs?

Thomas S Stockton

>Ken

The fit is a tight friction fit. If it is too loose it is real easy to pound the pegs in to far, if it is to tight the edges of the holes can start to crumble in. I do slightly under cut two edges but that is just to get the pegs started strraight, if one starts going in crooked I usually stop and pull it out. Thank Eddie for the jig he made it at a class taught by Darrell Peart, if you don't have his book it has some nice tips and details in it.

Tom

Re: How to make "pillowed" pegs?

#5

Re: How to make "pillowed" pegs? *LINK*

Stew Pharis

>Ken - Attached is a link showing another approach to making the pegs for G&G furniture. This is much like the one I learned in a class taught by Darrell Peart.

Darrell's book shows a jig for use with a disk sander. I haven't tried it yet but would expect it to be a big time saver if you have many pegs to make.


http://blogs.popularwoodworking.com/editorsblog/content/binary/GreeneandGreene.pdf

Re: How to make "pillowed" pegs?

#6

Re: How to make "pillowed" pegs?

Barry Irby

>I think I am too old to start on 72 hand made pegs.

I wonder if you couldn't chuck the stick in a lathe with the jaws removed from the chuck and sand the end with the various grits and part off the peg and do it again.... and again. I wonder if half inch square stock would pass through the shaft of my lathe? You could do about three and then advance the stick and do three more. Might even be able to power sand them. Why do it by hand the easy way when you can think of a much more complicated way involving power tools?

I once turned a nine foot long dowel on my two foot lathe just for fun.

Re: How to make "pillowed" pegs?

#7

Re: How to make "pillowed" pegs?

Thomas S Stockton

>That is another good way to do them. The only thing I would disagree with is sanding them to such a high grit I find that with a coat of finish you really don't need to go above 220 grit and if you feel like you want more polish you would save time by just hitting the ends on a buffing wheel.

Tom

Re: How to make "pillowed" pegs?

#8

Re: How to make "pillowed" pegs?

Ken Platt (Granby, CT)

>Barry, I had thought of using my lathe in exactly that way. But, I was afraid I would spend a lot of time getting the stem the right diameter to fit into the hole. I've done similar stuff a number of times, and I just have a hard time getting a consistent diameter. When I turned a bunch of tapered spindles for a shaker-style bench, I ended up having to number them and drill the holes with individually sized bits because of my inept sizing.

It's too bad I'm such a klutz at the lathe, because otherwise that'd be a neat way to do this.

Ken

Re: How to make "pillowed" pegs?

#9

Re: How to make "pillowed" pegs?

Barry Irby

>Ken, I was not thinking of turning the shaft, just "pillowing" the ends. Its a four jaw chuck and it would grip a small square stick perfectly.

If you wanted to turn the shafts, I suppose you could, but each one would be a pommel cut, which is transitioning from square to round. Tough to do without chipping the corners. You could use a saw to nick the corners, but I think the failure rate would be high. I also think they would be prone to fail later too, after they were installed.

I would punch the holes with a hollow chisel from the mortiser even if I did not own a mortiser. Just use the chisel and hit it with a mallet and get consistent square holes.

Mill the sticks to match the holes.

PS, next time you wish to turn matching tenons on pieces, use an open wrench of the right size as a feeler gauge. I hold the wrench in my left hand and make the cut with a square nosed scraper or parting tool in my right. Creep up on it and when the wrench drops on, you are there.

Re: How to make "pillowed" pegs?

#10

Re: How to make "pillowed" pegs?

Ken Platt (Granby, CT)

>Hey Barry, thanks for the tip on turning tenons. I figured there had to be an easy way.

I tried using the lathe to "pillow" the ends. It worked ok. I tried a variety of concave things to help make it uniform - bottom of a soda can, bottom of a medicine cup. After fiddling for awhile I decided I liked the flat-top pyramidal shape better for my piece, although I love the pillowed look in the pics in Peart's book (I'd forgotten I had it until this thread! I tend to buy too many books...)

Ken