General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Guy 9/17/07, 11:17 PM
4 Replies · 30 ViewsLast post 9/18/07, 12:25 PM by Mike Fitterling -
Removing the blade on a PC-557
by Terry Alexander 9/17/07, 12:42 PM
4 Replies · 31 ViewsLast post 9/18/07, 4:21 AM by DB -
OT: Okay, you AVG*ZA gurus…
by Rod Peterson -- Ormond Beach 9/17/07, 12:24 PM
5 Replies · 42 ViewsLast post 9/18/07, 3:20 AM by Jim Dillon -
Cutting large bevels (greater than 45 degrees)?
by JL 9/17/07, 3:16 PM
4 Replies · 80 ViewsLast post 9/18/07, 3:16 AM by Jim Dillon -
by Link Van Cleave 9/17/07, 5:02 PM
7 Replies · 60 ViewsLast post 9/18/07, 3:10 AM by Jim Dillon -
OT: Anyone tried the satelite TV on your PC
by Don Henthorn 9/15/07, 1:45 AM
2 Replies · 32 ViewsLast post 9/18/07, 1:32 AM by Don Henthorn -
by JL 9/13/07, 11:35 PM
10 Replies · 68 ViewsLast post 9/17/07, 11:57 PM by Greg Deavers -
Isn't a dust collection blowout a bad thing? *LINK*
by Mark in B'ham 9/17/07, 3:34 PM
3 Replies · 27 ViewsLast post 9/17/07, 7:35 PM by Dave Anderson Chester, NH -
by ben d. 9/9/07, 3:11 PM
6 Replies · 65 ViewsLast post 9/17/07, 3:50 PM by Lee Schierer - McKean, PA -
A BIG Thank you to Ray & Lynn - INDYFEST 2007
by Larry Clinton 9/17/07, 2:10 PM
0 Replies · 27 ViewsLast post 9/17/07, 2:10 PM by Larry Clinton -
by Eric M - San Jose 9/16/07, 2:25 AM
8 Replies · 41 ViewsLast post 9/17/07, 1:57 PM by Ray Carson, Lawrenceville NJ -
OT: Best way to add organic matter to a lawn
by wilbur 9/14/07, 12:13 AM
14 Replies · 50 ViewsLast post 9/17/07, 5:00 AM by Gary Camp Bend, Oregon -
by A.W. Ford 9/12/07, 8:52 PM
31 Replies · 347 ViewsLast post 9/17/07, 2:53 AM by Francisco -
by JL 9/13/07, 9:12 AM
20 Replies · 94 ViewsLast post 9/17/07, 1:41 AM by Evergreenbob -
Larry Clinton - Follow up Dust Collection question
by Curtis Gray 9/13/07, 10:35 PM
5 Replies · 38 ViewsLast post 9/17/07, 1:04 AM by Curtis Gray -
by Dustmaker Mike 9/14/07, 7:09 PM
5 Replies · 27 ViewsLast post 9/17/07, 12:30 AM by Bob Entwisle -
OT .. Need advice on weed eater technology..
by Jim Rahbe, Bedford, TX 9/15/07, 10:20 PM
11 Replies · 39 ViewsLast post 9/16/07, 11:22 PM by Jim Rahbe, Bedford, TX -
plastic wine corks make good little feet
by Wayland 9/16/07, 2:08 PM
1 Reply · 30 ViewsLast post 9/16/07, 10:38 PM by Clint Searl, at the base of Haycock Mtn -
by Larry in NW Ohio 9/14/07, 10:38 PM
11 Replies · 78 ViewsLast post 9/16/07, 10:29 PM by Larry in NW Ohio -
EXACT dimensions of 4x8 sheet?
by Brian in Sandusky 9/15/07, 12:47 AM
14 Replies · 93 ViewsLast post 9/16/07, 8:50 PM by Gary B -
by George 9/15/07, 8:35 PM
0 Replies · 29 ViewsLast post 9/15/07, 8:35 PM by George -
I followed Joe Pack's lead below
by Don Henthorn 9/13/07, 2:28 AM
5 Replies · 40 ViewsLast post 9/15/07, 6:51 AM by Martin from Granbury -
by Bill Kay 9/14/07, 10:49 AM
2 Replies · 26 ViewsLast post 9/15/07, 2:26 AM by Jim O in Davenport IA -
by A.W. Ford 9/12/07, 6:10 PM
15 Replies · 64 ViewsLast post 9/15/07, 2:24 AM by Art Silva -
3-1/4" Electric planer wisdom sought
by Pete in Holland, MI 9/13/07, 3:30 PM
11 Replies · 50 ViewsLast post 9/15/07, 1:43 AM by Mark Harrison - Brisbane, Australia -
by Stuart Johnson 9/14/07, 6:26 PM
4 Replies · 35 ViewsLast post 9/14/07, 7:27 PM by Stuart Johnson -
Update on what I thought was bad arbor bearings...
by Sue McLam in Orange, VT 9/14/07, 1:23 AM
11 Replies · 44 ViewsLast post 9/14/07, 6:29 PM by Don Henthorn -
Bit the bullet and ordered the 5 hp.. *LINK*
by JL 9/13/07, 3:43 PM
6 Replies · 47 ViewsLast post 9/14/07, 6:20 PM by Don Bullock -
by Ken Oakley-Sunny St. Cloud, Fla. 9/14/07, 5:06 PM
0 Replies · 26 ViewsLast post 9/14/07, 5:06 PM by Ken Oakley-Sunny St. Cloud, Fla. -
Finish for the interior of kitchen cabinets?
by JL 9/12/07, 6:11 PM
7 Replies · 68 ViewsLast post 9/14/07, 3:04 PM by jerry mayfield



