Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Update on what I thought was bad arbor bearings...

Posts

Update on what I thought was bad arbor bearings...

#1

Update on what I thought was bad arbor bearings...

Sue McLam in Orange, VT

>on my table saw.

You notice I said "what I thought"...Hah! My saw is a 10" Delta contractors saw. If you didn't read my last post about it, I had a clicking noise in the blade rotation...I even could hear it with my radio headphones on! I wanted to save as much money as possible so I decided to tear apart the saw myself and try to get the arbor out. I had to remove my homemade outfeed/router table, the front rail, and the right hand extension table. Then I could take the top of the saw off. On this particular saw there are 8 bolts to do that. Four of them simply go through the cabinet into the top; not a problem. The other 4 go through the trunion into the top. So basically by taking those out, the entire innards of the saw fall down. I'm thinking at that point that it's not going to be fun putting it back together.

So, after taking the top off I look at the arbor. The first thing I notice is that the jam nut on the far end of the arbor is loose; un-turned about an eight of an inch. Oh no, is that the only problem? Then I notice that there's a slot in the arbor for a key but I don't see a key. At this point I decide it's time to travel the 20 miles to my Delta sales/repair guy. To finally make a long story short, the key is actually part of the pulley and I didn't see it, and all the parts on the arbor were fine. The pulley is actually two pulley halves and the noise that I heard was them knocking against each other. He tightened the nut for me, put some loc-tite on it and sent me on my way. No charge because he felt bad for all I'd been through and what I was going to have to go through putting the saw back together! (Thank you Dave Spooner at Spooner Specialties in Montpelier!)

Time to take it apart was about 3 hours. Time to put it all back together and tuning was close to 5 hours. I now know more than I ever wanted to know about my saw.

Sue

Re: Update on what I thought was bad arbor bearings...

#2

But, Sur. Aren't you glad you have the experience

Don Henthorn

>and learning you got in that exercise? Just think how useful that will be in the future for yourself and for others who have problems. You go, girl.

Re: Update on what I thought was bad arbor bearings...

#3

Danged keyboard can't spell Sou.

Don Henthorn

>

Re: Update on what I thought was bad arbor bearings...

#4

Sue, either._______

Rod Peterson -- Ormond Beach

>

Re: Update on what I thought was bad arbor bearings...

#5

Re: But, Sur. Aren't you glad you have the experie

Sue McLam in Orange, VT

>Yes, Don, I am glad of the experience. I just wish the timing had been different. Sometime when I wasn't so busy. I feel fortunate that is only cost me time and not money!

Sue

Re: Update on what I thought was bad arbor bearings...

#6

Re: Update on what I thought was bad arbor bearing

The Mountain Man

>There is a pre-requeset (sp?) to being a woodworker and that is being to do exactly as you have dsescribed!! I've seen guys throw lots of money to get their power tools working correctly!!

Regards

The MountainMan

Re: Update on what I thought was bad arbor bearings...

#7

Re: Update on what I thought was bad arbor bearing

Michael Wangler in Rochester, NY

>Sue,

I almost went down the same road you just did. My cabinet saw starting making a funny noise when slowing down. I purchased new bearings and belts and rolled my sleeves up for a long job. Before I started doing the heavy work I call Jet technical support. They said my symptoms were likely caused by set screw in the arbor pulley. Sure enough deep down in one of the sockets an allen key backed out. A new set screw fixed me up quick.

Too bad I did not get the experience you did...

Re: Update on what I thought was bad arbor bearings...

#8

Re: Update on what I thought was bad arbor bearing

Jim Dillon

>Sue,

You undertook something not trivial by any means, while I would still be sitting, deep thinking about the problem, drinking lots of coffee - and never getting anything done. Good for you and thanks for getting back to us with what the problem really was; that might help me (and others) out in the future.

Jim

Re: Update on what I thought was bad arbor bearings...

#9

Re: Update on what I thought was bad arbor bearing

Sue McLam in Orange, VT

>Mountain Man,

I'm thinking that the people who can afford to pay someone to do what I did have some other day job to foot the bill! As a self-employed woodworker I gotta count those pennies.

Sue

Re: Update on what I thought was bad arbor bearings...

#10

Re: Update on what I thought was bad arbor bearing

Sue McLam in Orange, VT

>Michael,

I'm glad that you didn't have to go as far as I did! And if you're really sorry that you didn't get that experience, I think you should go ahead and do it anyway (tongue in cheek)!!!

Sue

Re: Update on what I thought was bad arbor bearings...

#11

Re: Update on what I thought was bad arbor bearing

Sue McLam in Orange, VT

>Jim,

Thanks. Yes, I wanted to post my results in case it'll help someone else save time in the future!

Sue

Re: Update on what I thought was bad arbor bearings...

#12

Heck, Rod, I guess it is time I stopped

Don Henthorn

>posting. I have to keep correcting my corrections. Blush!!!!!!