General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Chicago Bob 9/22/07, 4:44 PM
5 Replies · 36 ViewsLast post 9/23/07, 8:49 PM by Robert R Clough - Thorncraft -
by JL 9/22/07, 6:26 PM
8 Replies · 52 ViewsLast post 9/23/07, 8:09 PM by JL -
by Doug Reynolds in Seattle 9/23/07, 6:02 AM
6 Replies · 60 ViewsLast post 9/23/07, 7:54 PM by Ray Newman -
by Dave Winters 9/22/07, 3:40 PM
2 Replies · 33 ViewsLast post 9/23/07, 6:18 PM by Mark Mandell - Gone Round In Jersey -
by Guy 9/23/07, 1:47 PM
2 Replies · 31 ViewsLast post 9/23/07, 5:18 PM by Ron Hildreth, Alta, Iowa -
ran out of dye, will this work?
by Kelly Anderson 9/23/07, 12:04 AM
2 Replies · 31 ViewsLast post 9/23/07, 1:39 PM by McKay -
First Project: Advice welcome :)
by A.W. Ford, of Newberg, OR 9/17/07, 8:10 PM
20 Replies · 100 ViewsLast post 9/23/07, 12:55 PM by Al Stokka -
by Craig in Silverdale 9/22/07, 8:18 PM
9 Replies · 46 ViewsLast post 9/23/07, 6:20 AM by Craig in SIlverdale -
by Marc 9/21/07, 2:07 PM
9 Replies · 40 ViewsLast post 9/22/07, 11:25 PM by Thomas S Stockton -
by Norb - Cumming, GA 9/21/07, 2:56 PM
11 Replies · 43 ViewsLast post 9/22/07, 11:10 PM by Thomas S Stockton -
by Dave in Haverford, PA 9/19/07, 3:36 PM
15 Replies · 56 ViewsLast post 9/22/07, 2:15 PM by Larry Clinton -
by The MountainMan 9/20/07, 5:40 AM
15 Replies · 49 ViewsLast post 9/22/07, 1:47 PM by Larry Clinton -
Anyone have an 18" planer for hire? (central KY)
by Virgil Johnson 9/22/07, 2:26 AM
2 Replies · 31 ViewsLast post 9/22/07, 1:17 PM by Larry Clinton -
Does thickness of finish matter?
by Barry Irby 9/19/07, 12:49 PM
10 Replies · 98 ViewsLast post 9/22/07, 12:59 PM by Al Stokka -
by tek-Brunswick, Ohio 9/22/07, 10:40 AM
0 Replies · 32 ViewsLast post 9/22/07, 10:40 AM by tek-Brunswick, Ohio -
by Dan Donaldson 9/21/07, 3:13 AM
7 Replies · 38 ViewsLast post 9/22/07, 5:05 AM by DB -
OT - Where is the water going? !
by Ray Carson, Lawrenceville NJ 9/21/07, 12:58 PM
16 Replies · 57 ViewsLast post 9/22/07, 4:42 AM by DB -
by Ron Hildreth, Alta, Iowa 9/21/07, 12:34 AM
8 Replies · 64 ViewsLast post 9/21/07, 10:49 PM by Art Silva -
by Doug Reynolds in Seattle 9/21/07, 4:02 AM
9 Replies · 41 ViewsLast post 9/21/07, 10:44 PM by Art Silva -
by Edward McCormack 9/19/07, 8:18 PM
8 Replies · 61 ViewsLast post 9/21/07, 8:56 PM by George -
Hope I made the right choice / tool gloat
by Mike Schwing from Md. 9/18/07, 4:11 PM
13 Replies · 52 ViewsLast post 9/21/07, 8:16 PM by Don Bullock -
by Dave Winters 9/21/07, 5:12 PM
0 Replies · 27 ViewsLast post 9/21/07, 5:12 PM by Dave Winters -
Woodworking class opening at Kelly Mehler's.
by Martin from Granbury 9/21/07, 11:47 AM
2 Replies · 36 ViewsLast post 9/21/07, 4:25 PM by Martin from Granbury -
145 Replies · 588 ViewsLast post 9/21/07, 4:13 PM by Mark in B'ham
-
by George 9/21/07, 3:28 PM
0 Replies · 27 ViewsLast post 9/21/07, 3:28 PM by George -
by Kathy Heath-Palm Bay, FL 9/20/07, 4:32 AM
3 Replies · 36 ViewsLast post 9/21/07, 2:46 PM by Dennis Yoder -
Lucky to have 3 "Borgs" near me.
by Mike Circo 9/19/07, 3:29 PM
11 Replies · 44 ViewsLast post 9/21/07, 2:39 PM by Steve Schoene -
Saw blades. Sharpen or buy new?
by Tom Pilsbury 9/19/07, 11:01 PM
12 Replies · 38 ViewsLast post 9/21/07, 2:38 PM by Derek -
by Dave in Haverford, PA 9/20/07, 4:27 PM
3 Replies · 32 ViewsLast post 9/21/07, 2:05 PM by Steve Schoene -
Steam bending question: how much springback?
by Angus Barclay, in New Zealand 9/17/07, 11:21 AM
7 Replies · 81 ViewsLast post 9/21/07, 9:43 AM by Angus Barclay, in New Zealand



