Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Steam bending question: how much springback?

Posts

Steam bending question: how much springback?

#1

Steam bending question: how much springback?

Angus Barclay, in New Zealand

>I'm designing a 2-seater with a curved back. I figured that steam bending is probably the best way to get the curves I want. When the design is done and build time comes, this will be my first foray into steam bending.

My plan is to bend the stock over an appropriately curved form, with a flexible steel strap over the outer face of the board and close-fitting end-blocks at each end of the board. I'll clamp the stock to the form and can leave it clamped to the form for hours, days or even weeks if necessary.

Now to the question: Do steam bent components straighten out much after they've cooled and dried? If so, how much more curvature should I incorporate into the bending form to allow for any such springback? I've read articles here, on other websites and from a couple of books but noe of them adequately address this.

thanks in advance

Angus Barclay

Re: Steam bending question: how much springback?

#2

Ellis Walentine

Many variables

Ellis Walentine

>The amount of springback depends on the species, the radius of the bend, the thickness of the wood, the way you steamed it, etc. You have not seen it perfectly addressed because that's too many variables to come up with a definitive answer. The best way is to run a test and if the piece springs back more or less than you anticipate, modify the final form accordingly.

Ellis

Re: Steam bending question: how much springback?

#3

Re: Many variables

Lee Ohmart

>I had this issue when I made an ash runner for a sled I made for my dog to pull my daughter around in. One was already bent from a salvaged sled and I had to match it. I made a form, bent the ash and dried it and the result did not match. The form was modified based on the difference between the form and the first runner. The resulting runner was a match.

Re: Steam bending question: how much springback?

#4

Jesper, Denmark

Re: Steam bending question: how much springback?

Jesper, Denmark

>If you are bending solid stock, you will likely fix either end in the final product, so springback should not be such a big deal.

If laminated stock, 7 layers or more do not spring back when glued in the form.

Re: Steam bending question: how much springback?

#5

My take is that there are times to

Don Henthorn

>laminate and there are times to steam. I always went by a simple rule. If the piece was to be fastened at both ends I would steam if possible. If either end was not to be fastened I would laminate. This worked for all the stuff I did, but I could see a case or two where this might not be appropriate. In that case a little trial and error with steaming might work.

Re: Steam bending question: how much springback?

#6

A big THANKS for the bending advice

Angus Barclay, in New Zealand

>Based on the advice here, this is an appropriate time to steam rather than laminate. The curved back of the 2-seater will be fixed at both ends. The design is such that the curved piece will be highly visible on both a face and an edge, so I want to avoid lamination and the need to get perfectly tight glue lines for an acceptable result.

The species is kauri and I guess I'll find out soon enough how much spring back I get with a 7/8ths thick board soaked for a couple of weeks in a water trough then steamed for 60 minutes.

Based on the advice given here, I expect to modify the bending form at least once and I'll have a couple of spare blanks on hand to cope with the entitely foreseeable but still unavoidable SNAFUS that form part of the learning curve for any new technique.

Thanks again for the helpful advice.

regards

Angus Barclay

Re: Steam bending question: how much springback?

#7

Re: A big THANKS for the bending advice

Keith Newton

>Angus, I have never used that wood, but I was under the impression that it was a pretty soft wood. This may make it harder to bend if the cells are longer thin-wall.

Re: Steam bending question: how much springback?

#8

Re: A big THANKS for the bending advice

Angus Barclay, in New Zealand

>Hello Keith,

kauri is a reasonably dense softwood. I don't know anything about the length of the cells or if they are thin walled but I did find a book today that says it is not suitable for steam bending. I'm the kind of guy who sometimes has to learn the hard way, so I still intend to give it a try but I'm working on a "plan B" too.

regards

Angus Barclay