Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

EXACT dimensions of 4x8 sheet?

Posts

EXACT dimensions of 4x8 sheet?

#1

EXACT dimensions of 4x8 sheet?

Brian in Sandusky, OH

>If I'm not mistaken, a 4x8 sheet of MDF, plywood, etc is actually 97" x 49", right? (long story, but my shop space has been VERY small for about a year now. It's been a while since I bought a full size sheet of plywood, I'm embarrassed to say...)

The reason that I ask is that I'm finally breaking ground on a new shop soon, and I just sold my truck (gas prices, insurance, etc.) and I'm buying a trailer to put behind my car.

One trailer that I'm looking is has EXACTLY 96" of internal length. No more. A 97" sheet will not fit.

I think that I need to go a size bigger on the trailer, right?

Re: EXACT dimensions of 4x8 sheet?

#2

Re: EXACT dimensions of 4x8 sheet?

Lee Schierer - McKean, PA

>I believe 4 X 8 sheets are exactly 48 X 96. I never heard of a 97" sheet of anything.

Lee

Re: EXACT dimensions of 4x8 sheet?

#3

Re: EXACT dimensions of 4x8 sheet?

Robin Corell, in Atascadero CA

>construction ply and particle board are 48"x96". MDF is usually 49"v97" but I have seen it at exact size.

If the trailer is enclosed or has sides is there any reason you couldn't stand the sheet goods on edge and run them diagonally?

Robin

Re: EXACT dimensions of 4x8 sheet?

#4

Some mdf is

Dan Donaldson

>

Re: EXACT dimensions of 4x8 sheet?

#5

trimming allowance

Andrew F in Australia

>Over here, they're close to 4' by 8'

1220 by 2440mm is what is standard.

(1' = 305mm)

Extra dimension may be trim allowance.

Cheers,

Andrew

Re: EXACT dimensions of 4x8 sheet?

#6

EXACTLY Right

David Yoho

>Brian, my experience has been that MDF is indeed 97" x 49". So, if you'll be hauling much of it in the future, it looks like a little longer trailer will be in order. This could come in handy for other items too. Some of the solid stock I buy that's sold as 8' is usually a tad longer.

David

Re: EXACT dimensions of 4x8 sheet?

#7

Jason Roehl in Lafayette, IN

Last time I checked...

Jason Roehl in Lafayette, IN

>1" = 254mm, not 305mm

Some construction ply is actually LESS than 4'x8', by about 1/16"-1/8" in each dimension. The reason is so that you can maintain the proper spacing of 1/8" on a roof and still land the seams on a truss. If they were the full 4'x8', and you did the 1/8" gap you're supposed to, after about 3 sheets you would have an end flapping in the breeze.

Jason

Re: EXACT dimensions of 4x8 sheet?

#8

Re: Last time I checked...

Al Stokka - Cambridge, Iowa

>1" = 25.4 mm.

Andrew said 1' = 305 mm, not 1".

Al

Re: EXACT dimensions of 4x8 sheet?

#9

Re: EXACT dimensions of 4x8 sheet?

Gene Gauss

>A trailer that can't accomodate a little overhang might well be a problem for carrying anything that is exactly the same length as the bed. You need a little tolerance for stacking, picking it up, etc. Does it have a tailgate that can be removed or lowered? Gene Gauss

Re: EXACT dimensions of 4x8 sheet?

#10

Re: EXACT dimensions of 4x8 sheet? *LINK*

Brian in Sandusky, OH

>Thanks everyone.

The bigger trailer is only a couple hundred more, so I'll probably go with it.


Trailer

Re: EXACT dimensions of 4x8 sheet?

#11

Re: Tire caution

Kneale Brownson in sunny N. MI

>I see your link lists tires as "four-ply" without any other designation.

In some states, there is a trailer tire requirement that says trailers must be provided with trailing-specific rubber, not car take-off tires, etc. Check your local laws. In Michigan, trailer tires, regardless of trailer size/configuration, must bear a trailer designation cast into the sidewall. The state collected some pretty hefty fines as a result of increased attention to this rule last year.

I wouldn't rely on the trailer sales outlet to provide information on this regulation.

Re: EXACT dimensions of 4x8 sheet?

#12

Re: EXACT dimensions of 4x8 sheet?

Dave Bair, Eaton Rapids, MI

>The last batch of hardwood plywood I bought measured 97x49. The guy helping me load said some makers are still going with 96x48. At $80-110 a sheet, I appreciate that extra inch and it still fits into the bed of my Chevy.

Re: EXACT dimensions of 4x8 sheet?

#13

1"=25.4mm, 1' = 12" = 305mm approx

Andrew F in Australia

>Hi Jason,

I was trained in both metric and imperial.

No hard feelings my side.

Cheers,

Andrew

Re: EXACT dimensions of 4x8 sheet?

#14

Yummy crow.

Jason Roehl in Mulberry, IN

>You guys are right. Open mouth, insert foot. I read it as one inch, not one foot, then managed to get the conversion wrong. And I, too, was trained in both English and metric units. My apologies, Andrew.

Jason

Re: EXACT dimensions of 4x8 sheet?

#15

Re: EXACT dimensions of 4x8 sheet?

Gary B

>Alot of Engineered wood products, especially from commercial suppliers come 1" larger then spec'ed, as someone already stated for a trim allowance....so if you buy a sheet of MDF, Particle board, or some plywood from a wholesaler, expect it. In fact, the only thing I know of that comes in consistently exact is Solid surface, you can expect that to be 30" x 144"