General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Cody Lewis in LV 2/26/08, 9:31 PM
7 Replies · 35 ViewsLast post 2/27/08, 10:21 AM by JL -
by John K Jordan 2/25/08, 8:17 PM
9 Replies · 65 ViewsLast post 2/27/08, 12:28 AM by John K Jordan -
OT- So, you think you know your geography? *LINK*
by Joe Pack 2/26/08, 3:58 PM
12 Replies · 36 ViewsLast post 2/26/08, 9:14 PM by JoeW in Detroit, MI -
by Forrest Addy 2/26/08, 5:17 PM
3 Replies · 78 ViewsLast post 2/26/08, 7:43 PM by Forrest Addy -
by Howard D 2/25/08, 8:36 PM
10 Replies · 42 ViewsLast post 2/26/08, 7:30 PM by Ellis Walentine -
by Joe Burke 2/25/08, 3:28 PM
11 Replies · 35 ViewsLast post 2/26/08, 5:24 PM by Mark Goodall - ATL - tooljunkie -
by Stephen Shepherd in the State of Deseret 2/26/08, 1:48 PM
0 Replies · 28 ViewsLast post 2/26/08, 1:48 PM by Stephen Shepherd in the State of Deseret -
OT Can some body Explain "Green" and Carbon.....
by Barry Irby 2/24/08, 8:33 PM
19 Replies · 65 ViewsLast post 2/26/08, 12:36 PM by Barry Irby -
by JohninRI 2/24/08, 12:07 AM
3 Replies · 30 ViewsLast post 2/26/08, 11:03 AM by JohninRI -
by John E 2/25/08, 5:33 PM
6 Replies · 46 ViewsLast post 2/26/08, 4:17 AM by John Cotten -
OT: Garage door opener help please
by Mike Schwing from Md. 2/25/08, 1:15 PM
17 Replies · 36 ViewsLast post 2/26/08, 2:44 AM by Mark Goodall - ATL - tooljunkie -
by Bart Goldberg 2/25/08, 2:08 PM
6 Replies · 33 ViewsLast post 2/26/08, 2:16 AM by David Yoho -
Ellis, did you get my Fri and Sun E-Mails?
by Robert R Clough - Thorncraft 2/26/08, 1:29 AM
2 Replies · 20 ViewsLast post 2/26/08, 2:10 AM by Robert R Clough - Thorncraft -
WC Weekend Accomplishments.....
by Dennis E. Peacock 2/25/08, 3:00 PM
2 Replies · 23 ViewsLast post 2/26/08, 1:38 AM by George -
by Denis Ch�nard, Orl�ans, Ont. 2/24/08, 1:34 PM
10 Replies · 32 ViewsLast post 2/26/08, 12:45 AM by Malcolm Timbers -
by Thomas S Stockton 2/24/08, 8:59 PM
5 Replies · 27 ViewsLast post 2/26/08, 12:38 AM by Dan Donaldson -
Sliding dovetail or mortise & tenon?
by JL 2/25/08, 10:28 AM
9 Replies · 63 ViewsLast post 2/25/08, 10:28 PM by Mark Mandell - Gone Round In Jersey -
by Howard 2/25/08, 8:06 PM
4 Replies · 22 ViewsLast post 2/25/08, 10:13 PM by Dustmaker Mike -
by Terry Alexander 2/25/08, 9:16 PM
4 Replies · 28 ViewsLast post 2/25/08, 9:45 PM by John E -
Dresser Rehab Finishing Question
by Tony - Memphis 2/25/08, 8:07 PM
1 Reply · 21 ViewsLast post 2/25/08, 9:04 PM by Lee Schierer - McKean, PA -
by Jeff Weaver 2/21/08, 10:57 PM
14 Replies · 75 ViewsLast post 2/25/08, 5:38 PM by Jeff Weaver -
by Dan Collins 2/23/08, 2:12 AM
4 Replies · 26 ViewsLast post 2/25/08, 5:30 PM by Lee Schierer - McKean, PA -
by Jerry Gibbs 2/23/08, 11:54 PM
4 Replies · 36 ViewsLast post 2/25/08, 5:23 PM by Lee Schierer - McKean, PA -
About safety. (Warning: Extremely graphic)
by Tom Pilsbury (Chicago) 2/24/08, 1:08 AM
8 Replies · 37 ViewsLast post 2/25/08, 4:59 PM by Brian in Brighton -
Scribing top for inset cabinets
by Howard 2/25/08, 3:47 PM
0 Replies · 23 ViewsLast post 2/25/08, 3:47 PM by Howard -
Poached hardwood (from the Seattle Times)
by John D. Luke 2/25/08, 3:16 AM
2 Replies · 58 ViewsLast post 2/25/08, 2:49 PM by Robert R Clough - Thorncraft -
by David Yoho 2/25/08, 2:16 PM
0 Replies · 23 ViewsLast post 2/25/08, 2:16 PM by David Yoho -
by GarryF 2/23/08, 2:23 AM
11 Replies · 37 ViewsLast post 2/25/08, 2:06 PM by Bruce, a MN Galoot -
TS: Square at 0 deg but not at 45 deg?
by Dominic Greco in Richboro PA 2/23/08, 8:57 PM
9 Replies · 37 ViewsLast post 2/25/08, 12:57 PM by Dominic Greco in Richboro PA -
by Tim Caley - North Little Rock 2/23/08, 5:56 PM
6 Replies · 39 ViewsLast post 2/25/08, 4:44 AM by Tim Caley - North Litttle Rock



