Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

TS: Square at 0 deg but not at 45 deg?

Posts

TS: Square at 0 deg but not at 45 deg?

#1

TS: Square at 0 deg but not at 45 deg?

Dominic Greco in Richboro PA

>OK, I'm going a little crazy here!

I just spent my afternoon trying to tweak a cross cut sled for my Unisaw only to find that it's giving me DEAD on square cuts at 0 deg (90 deg to the table) and NOT square cuts when I set the blade to cut 45 deg!

I had made this nifty cross cut sled last week and got it so I could make dead on square cuts. I cut some nice wide test pieces and was able to verify that I was getting perfectly square cuts. HOWEVER today when I went to change the blade angle, all hell broke loose. I thought that I had a made an error and that I needed to re-set the fence. At this point I thought that the piece of plywood I was using as a fence was flexing under load. So I scrapped it and made a nice sturdy L-Shaped fence out of (2)pieces of plywood and started over.

But as soon as I tilt the blade it goes out again! I used my 12" Starrett square to check the pieces and I'm out about 1/32" over 9".

Has anyone else ever had this problem? I used to expect this kind of thing from my old Craftsman Contractor Saw. But not my Unisaw!

And is 1/32" over 9 or 10" something to get upset over?

See ya around,

Dominic

Re: TS: Square at 0 deg but not at 45 deg?

#2

Re: TS: Square at 0 deg but not at 45 deg?

tek-Brunswick, Ohio

>Are you sure that your sled is dead flat and parallel to the table and the piece you are cutting has parallel sides? Any deviation from parallel to the table will show up at any angle other than 90%. Are you clamping your piece to the sled ? The blade will try to push the piece away from the 45% side of th blade. Creeping will make it go out of square. That is two things that could be the problem and are not the saw.

Re: TS: Square at 0 deg but not at 45 deg?

#3

Re: TS: Square at 0 deg but not at 45 deg?

Robin Corell in Atascadero, CA

>This is a simple but extreamly tedious fix. You need to remove the top on your saw and change the shims under the trunions. most saws have shims under the trunions with unused shims under the washer at the bolt head. change one shim at a time and reinstall the table and true it to the blade at 90* check at 45* and repeat as often as it takes to get to acceptable results.

Plan on spending most of an afternoon making the nessesary adjustments.

Robin

Re: TS: Square at 0 deg but not at 45 deg?

#4

Robin is almost right

Keith Newton------WebKitFormBoundaryDZmgloT+ZiYFgX

>Since the trunion is attached to the base, the shims need to be between the top and the base.

Two things to check first. If a blade is dull on one side, it will deflect to the path of least resistance. This is true even if it is dull on both sides when tilted to 45�.

If you are sure your blade is sharp. Crank it all of the way up, and tilt to 45�. This will compound the problem more than a lower setting. then cut something like MDF on the sled, and watch carefully while the back of the blade is passing through the kerf. After making the cut, inspect the tooth marks on each part.

If the back of the blade is cutting its own path on the top of the bevel, you need to raise the back of the table, or lower the front. If it is cutting the heel of the bottom, which is what I have seen a couple of times, you need a couple of washers under the table in the front.

Just remember that a dull blade cutting hard material will deflect like a rock skips over the surface of water, so don't go wasting time making adjustments to a saw with a dull blade.

Re: TS: Square at 0 deg but not at 45 deg?

#5

Re: TS: Square at 0 deg but not at 45 deg?

Dominic Greco in Richboro PA

>Thanks for your response. The sled is made from dead flat MDF and the test pieces were cut after tweaking the TS fence and aligning it dead on. I made sure to hold the pieces firmly and allowed no movement while cutting. HOWEVER, that being said I understand what you are saying.

Re: TS: Square at 0 deg but not at 45 deg?

#6

Re: Robin is almost right

Dominic Greco in Richboro PA

>Keith,

You wrote:

"Two things to check first. If a blade is dull on one side, it will deflect to the path of least resistance. This is true even if it is dull on both sides when tilted to 45�."

I'm glad you mentioned that. I would have never thought of it. The test pieces I was using were MDF. And not much is harder than that stuff! And I'm using a Forrest WWII blade that could definitely benefit from being sharpened. I will install a sharp Freud blade I use as a back up and test it out tomorrow.

Thanks,

Dominic

Re: TS: Square at 0 deg but not at 45 deg?

#7

Thanks Robin

Dominic Greco in Richboro PA

>Robin,

Thanks for the response. I have never had the chance to remove the table from a Unisaw. So I'll probably need to do some research first before I attempt to do this. I seem to remember a couple WWing articles that addressed this problem.

Thanks again,

Dominic

Re: TS: Square at 0 deg but not at 45 deg?

#8

Re: TS: Square at 0 deg but not at 45 deg?

Dominic Greco in Richboro PA

>Hi Everyone!

I just wanted to give those interested an update on my progress in addressing the problems I was having getting square cuts from my Unisaw when the blade was set at 45 deg.

Keith Newton had recommended that I check to see how sharp the blade was. And I was glad I checked before I started adjusting the table and what not! The Forrest WWII blade I was using had not been sharpened since 2004 and had seen some rough duty since that time. (Needless to say, I'm sending it off to be sharpened tomorrow!) I replaced it with an almost new Freud Combo blade and was able to get dead on cuts almost right off the bat.

Bob (rfeeser) from Woodnet recommended that I clamp the workpiece so it doesn't move when you cut it. I had some nice old Destacco clamps (liberated from a dumpster at my old job!) laying around. So I used them for hold downs. Since I didn't want to mar the workpiece, I replaced the bolt with a machine leveler I had. Luckily I had two, so both clamps got a retrofit.

In order to make "sneaking up" on 90 deg easier, the fence features an adjustment block near the end. I just inset a T-nut into a block of wood. Then got a piece of metal and bent it at 90 deg. This metal angle got attached to the fence and gave me something for the jack screw to bear against. All you need to do is turn the bolt one way or the other to increase or decrease the fence angle.




After I added the clamps to the sled and checked out at the settings, it was time to make the cuts. I had to make (24) 45 deg cuts and each went as smooth as silk.

Thanks again for all the help!

See ya around,

Dominic

Re: TS: Square at 0 deg but not at 45 deg?

#9

Re: TS: Square at 0 deg but not at 45 deg?

Keith Newton

>Hey Dominic, Thanks for coming back and filling us in. It is always nice to hear when someone actually takes my advice, and especially if I made a lucky guess and saved you the time of chasing after the wrong problem. I am glad that was all there was to it. K

Re: TS: Square at 0 deg but not at 45 deg?

#10

Re: TS: Square at 0 deg but not at 45 deg?

Dominic Greco in Richboro PA

>No problem! I appreciate the advice. And after changing the blade out, it worked so well I was dancing! :>)