General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Dustmaker Mike 2/15/11, 12:55 AM
1 Reply · 20 ViewsLast post 2/15/11, 3:18 AM by Bill Houghton -
by Ed Beck 2/13/11, 4:27 PM
23 Replies · 113 ViewsLast post 2/15/11, 2:46 AM by Ed Beck -
by Mark 2/13/11, 1:07 PM
15 Replies · 43 ViewsLast post 2/15/11, 1:17 AM by John in NM -
DIY Home With Incredible Features *LINK*
by charlie belden 2/14/11, 7:17 PM
0 Replies · 14 ViewsLast post 2/14/11, 7:17 PM by charlie belden -
by George 2/13/11, 2:07 AM
30 Replies · 49 ViewsLast post 2/14/11, 5:09 PM by Lee Grindinger -
Mid-West boy to go to Frank Miller....
by roger lance 2/14/11, 2:40 PM
2 Replies · 11 ViewsLast post 2/14/11, 4:27 PM by Larry in NW OHIO -
Table Saw Repair? Or Replace? (long)
by Rick Lasita 2/13/11, 12:54 PM
17 Replies · 60 ViewsLast post 2/14/11, 4:21 PM by Jim DeLaney, Austintown, Ohio -
by Scott in Montana 2/13/11, 11:09 PM
10 Replies · 35 ViewsLast post 2/14/11, 3:16 PM by Grant in Iowa -
I broke my blade guard on my Grizzly 1023
by David C. Lykins - Dallas GA 2/11/11, 7:03 PM
7 Replies · 20 ViewsLast post 2/14/11, 2:15 PM by AZ -
by Bill Houghton 2/12/11, 1:53 AM
13 Replies · 32 ViewsLast post 2/14/11, 1:42 PM by Lee Schierer McKean, PA -
by laurie power 2/12/11, 11:37 PM
15 Replies · 24 ViewsLast post 2/14/11, 1:31 PM by Lee Schierer McKean, PA -
by Jennifer@Indy.USA 2/11/11, 2:24 AM
26 Replies · 81 ViewsLast post 2/14/11, 1:54 AM by BrianA -
Going to Atlanta, GA tomorrow to pick up my RAS!
by Charles Jackson III 2/13/11, 10:56 PM
0 Replies · 23 ViewsLast post 2/13/11, 10:56 PM by Charles Jackson III -
by Larry in NW OHIO 2/13/11, 4:14 PM
0 Replies · 18 ViewsLast post 2/13/11, 4:14 PM by Larry in NW OHIO -
Anyone replace W-strip in patio door?
by Barry Irby 2/12/11, 10:49 PM
2 Replies · 11 ViewsLast post 2/13/11, 3:48 PM by Larry in NW OHIO -
by Jennifer@Indy.USA 2/13/11, 12:14 AM
3 Replies · 12 ViewsLast post 2/13/11, 3:40 PM by Keith Newton----Little Rock, Arkansas -
by Clint Searl 2/11/11, 2:38 PM
8 Replies · 10 ViewsLast post 2/13/11, 3:08 PM by Mark Mandell - Gone Round In Jersey -
"Fraternity proof" finish for coffee table?
by JL 2/12/11, 2:04 PM
11 Replies · 18 ViewsLast post 2/13/11, 1:29 AM by JL -
Makita wet sharpener on Benefits Auction
by Neal in San Jose 2/13/11, 1:16 AM
0 Replies · 27 ViewsLast post 2/13/11, 1:16 AM by Neal in San Jose -
ISO suggestions for protecting plywood from water
by ILYA Z 2/11/11, 5:20 PM
6 Replies · 15 ViewsLast post 2/12/11, 4:20 PM by Howard Acheson -
by David C. Lykins - Dallas GA 2/12/11, 2:29 PM
1 Reply · 18 ViewsLast post 2/12/11, 2:55 PM by Barry Irby -
by Virgil Johnson 2/8/11, 2:19 AM
3 Replies · 13 ViewsLast post 2/12/11, 2:35 PM by David C. Lykins - Dallas GA -
by Roger Lebas 2/8/11, 2:33 AM
3 Replies · 19 ViewsLast post 2/12/11, 2:33 PM by David C. Lykins - Dallas GA -
Help Choosing a Lunchbox Planer
by DP 2/9/11, 6:11 PM
10 Replies · 16 ViewsLast post 2/12/11, 2:04 PM by Dave Paine -
Delta sold to Taiwanese Co. *LINK*
by Moses Yoder 2/11/11, 1:07 PM
1 Reply · 19 ViewsLast post 2/11/11, 11:42 PM by Chuck Lenz -
by Thomas Norton 2/10/11, 10:57 PM
11 Replies · 23 ViewsLast post 2/11/11, 10:32 PM by Barry Irby -
Anyone hang a drawer from the top?
by Barry Irby 2/10/11, 8:21 PM
11 Replies · 30 ViewsLast post 2/11/11, 8:59 PM by FredD -
by Alan Young 2/10/11, 7:03 PM
20 Replies · 51 ViewsLast post 2/11/11, 7:10 PM by Alan Young -
What would you do with this Jointer???
by Thomas Skaggs 2/10/11, 8:23 PM
20 Replies · 20 ViewsLast post 2/11/11, 5:38 PM by Michael Wangler -
by JL 2/10/11, 2:14 AM
2 Replies · 10 ViewsLast post 2/11/11, 1:43 PM by Mark_in_Michigan



