Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Calling all Lefty's

Posts

Calling all Lefty's

#1

Calling all Lefty's

Mark

No politics here.

My 15 year old "left handed" son is getting more and more interested in the Shop and WW lately.

He is about to start a woodworking course at High school this semester and as we were talking in the shop about WWing and safety techniques generally, he took a push stick in his left hand (table saw off) and went through the motion of pushing (rip cut)a board though the TS, asking if this was the right way to do it, where to put the pressure, etc. etc.

First off, I had taken the saw guard off to cut a panel earlier, and that is not usually the case especially if he was going to use it.

However, that's when I noticed that with the fence set to the right of the blade (for me right handed), and with him using his left hand to push the stock, his whole hand and arm would be crossing directly over the blade or getting hung up on the guard.

Using his left hand to push with the fence to the right isnt safe.as its hard/impossible for that left arm not to bend out like a wing

Can't be the way!

So I started wondering how other Lefty WWs work

Question...How do you Left handed WW's use the table saw?

Do you rip with the fence to the left of the blade and reverse most set ups?

Same question for using the mitre gauage do you use the right mitre slot for cross cuts?

Do you just teach yourself to work as a right hand person would?

Curious...Thnx Mark

Re: Calling all Lefty's

#2

Good Question

Mark Mandell - Gone Round In Jersey

Being right handed (a/k/a left-brained) I have developed my ability to operate southpaw in the shop; especially when it comes to rip-sawing. I actually use the push stick with my left hand, but when I do so, I am standing on the right side of the fence so that my left arm and shoulder are also to the right of the blade. I do so, while using feather boards to keep the workpiece tight to the fence, so that if the off-cut piece (left of the blade) should decide to reverse its direction, I am not standing in the launch window plus I can use both hands to control the important part of the board, that being 'tween the blade and the fence. It also prevents my left thumb from testing whether it's time to have the blade sharpened. I tried that once; I retained the thumb and the lesson.

You might also remind him to set the blade height to just clear the top of the board. You get better dust collection and greatly reduce the risk on body parts contacting sharp spinning objects.

You should also show him how not to push wood through the meat, er, band saw, then move on to the jointer and SCMS (or RAS), and then do the full circuit again.

Re: Calling all Lefty's

#3

I work like a right handed person

Bill Houghton, Sebastopol, CA

Most lefties have to learn how to work righthanded for at least some tasks; this is one of them. Very few, if any, tablesaws are sold with much of any rip capacity to the left of the blade.

Re: Calling all Lefty's

#4

Re: Calling all Lefty's

Robert R. Clough

I generally work as a R handed person, but it makes little difference as I can use either hand equally well. When ripping I have never had a piece to the left of the saw (outside) shoot back, but I have had that piece between the fence and saw do so. Of course I do not have my feather bd really tight, just rather loosely there to keep things on track.

Re: Calling all Lefty's

#5

Re: Calling all Lefty's

Dave Paine

I am mostly left handed. I push the work with my left hand, scribe with my left hand, etc.

I use the fence at the right side of the blade.

I am not sure why you feel your son would have a hand or arm crossing the blade.

I stand at the right side of the blade and feel very comfortable pushing the stock with the left hand. I always use a push aid - stick or similar. The only reaching I do is to turn the saw on or off.

The only time my left arm is to the left of the blade is when I am using the mitre gauge on the right side, and I use the left arm with a push stick so that the drop is pushed through to get a clean edge.

All the table saws I have ever seen are designed with the larger cut capacity to the right of the blade. I have 36in to the right and 13in to the left.

I rarely move the fence to the left side of the blade. One example would be to cut e.g., a strip out of a wide piece of plywood where I am constrained by the garage steel support column for the upper story to the left of the saw.

The only tool I can think of which is difficult for me to use left handed is a pair of scissors.

Re: Calling all Lefty's

#6

PS

Mark Mandell - Gone Round In Jersey

I did leave out that I don't even use a miter gauge. I have and use several cross-cut sleds. I think the miter gauge thingy is in a box somewhere, probably with the cosmoline still on it. ;)

Re: Calling all Lefty's

#7

Re: Calling all Lefty's

woodenleg

I have to agree with most of the lefty's. You have to start learning how to use your right hand. I have found that lefty's that have learned to use their right hand are better than most righty's, we can use almost any tool with our left and right where righty's have trouble with left. At first he will feel useless, it just takes time but them more he uses his right the better he will be. One thing you should find out is what eye is the master, for me it is my right. That really makes a difference when using hand saws and other tools that rely on the eyes. Good Luck Dave

Re: Calling all Lefty's

#8

Re: Good Question

Joseph Mulherin, Sr

I must say we find very interesting questions here on WC. For my comment on the righthand/lefthand usage....well I guess I am most blessed because I have been gifted to be ambidextrous....my Mom just laughed at me when I got into a tight spot hammering and switched the hammer to the other hand and kept on doing the job at hand. Shooting guns; cutting boards on my Shopsmith is never a problem because it has extension tables I can slide on added poles and switch the fench to whatever measurement I need. That way I can cut almost everything that comes up with both hands....whichever is better for the project I am making.

The Shopsmith is the 510 model setup and suits my woodworking fine. Also have other hand tools I use both ways.

Re: Calling all Lefty's

#9

Re: Calling all Lefty's

Lee Daley

Let's face one simple fact, all lefthanders who have all digits and limbs intact are very intelligent and adaptable. We have to be! The world is against use from using scissors in kindergarten! in 1970's most military weapons were decidedly NOT ambidextrous. You even had to hold a hand grenade upside down to use it safely. I survived! Basically, you have to teach your son to first embrace his lefthandedness, and find ways to deal. Then find ways to be safe. Cutting a panel of plywood to size is a challenge to a lefty. your strong hand will want to hold the saw with the weight on the cutoff side, not safe especially at a 4' extension. And the go......med 'safty interlocks are WRONG for US, and sometimes force you to grip the tool unsafely. Table saw is somewhat simple, move the fence to the Wrong side of the blade, and if shop teacher complains, question his knowledge of teaching lefties, and then threaten to sue. But bottom line your son will have to become more ambidextrous, and safely adapt

Good Luck

Re: Calling all Lefty's

#10

Re: Calling all Lefty's

Mark

So ....bottomline if I am reading this correctly is learn to use the saw the way a right hander does......good points about TS design ripping width being to the right of the blade etc.

I have not mentioned this to him and I think like most of the reponders do, I will teach him to use the TS ( as a righty if you will ).. but safely..what ever works but safe

We made some progress today on a golf ball display rack he fancied. Used up some scrap cherry and he did great crossing and ripping on the TS without any change or set up from what i would use.

Spent all day in the shop with him and it was a blast!

With him being 15 you just know those days are numbered...!

Thanks Mark

Re: Calling all Lefty's

#11

Same here

Phil Joines

Re: Calling all Lefty's

#12

Re: Calling all Lefty's

AZ in Colorado Springs

I'm a southpaw. As others have noted, most saws have less table to the left of the blade, so I do most cuts with the fence to the right of the blade.

I find it difficult in many situations to avoid standing right behind the blade, though, for a cut to either side. When ripping a narrow workpiece, one hand guides to stock tight to the fence (from the waste side of the cut) while the other hand pushes the workpiece through the cut (I hear it coming -- get a featherboard). When using a sled or mitre for a crosscut I can stand all to one side of the blade (& when ripping a piece wide enough that I can control and push it without getting my fingers near the blade and risk becoming a statistic in Glen Huey's current TS safety inquiry).

As far as hand tools go, I work mostly left handed, but sometimes the workpiece makes it impossible -- trimming a dovetail joint or doing some other task in a "confining" location or position.

Re: Calling all Lefty's

#13

Re: Calling all Lefty's

Joe in a Cleveland suburb

"Spent all day in the shop with him and it was a blast! "

That's great Mark. I always wished my (now 19 y.o.) son has an interest in ww'ing.

Re: Calling all Lefty's

#14

Left handed here and confused...

Joe in a Cleveland suburb

Sorry, I've been that way since I was born; left handed and confused.

In general, when not using a crosscut sled, I have the fence to the right of the blade. I use a splitter all the time (well when the cut permits). I use a feather board and a push stick all the time (when the cut permits). I don't have/use a blade guard.

I push the stock through with my RIGHT hand while standing left of the blade.

I do feel a little uncomfortable doing that, but I feel I have better control of the piece being cut opposed to using my left hand to push and standing right of the blade. So, my right hand does pass over the blade.

By using my right hand there is a normal tendency to keep the stock pushed up tight to the rip fence. I feel when I stand right of the blade and push with my left hand, it is harder to keep the stock tight against the rip fence.

If I am cutting something big enough (like cutting down a piece of ply) where there is room to stand between the blade and fence, I will stand right of the blade.

I have tried using the rip fence left of the blade, but it doesn't "feel" right.

Is this the wrong approach?

Do I need to relearn/re-think what I am doing.

Thanks.

Re: Calling all Lefty's

#15

Re: Calling all Lefty's

Ron Jones

I'm kind of an odd ball I guess. I write left, throw right, golf right, hit from either side, and do all woodworking right including what little turning I do. I also taught woodworking for many of my 42 years in the classroom. My left handed students operated ww equipment as a righty. That's the way the equipment is intended to be used. Teach him the right handed way as if it is expected--not an option.

Re: Calling all Lefty's

#16

No need to re-learn....

John in NM

First and foremost, use the machine in the way that is most comfortable for you, I find awkward positions and methods more likely to result in an accident.

Though I'm right handed, I tend to work exactly as you describe, except for rarely using feather boards - I use a second push stick instead, held in the left hand. I find it a good substitute for both the feather board and splitter. Basically just a stick with a notch cut in the end that can push against the work where ever I need it, usually behind the blade. If the kerf is trying to close up, jamming this stick in there prevents it.

So I don't think you need to re-learn anything, but then I wouldn't, working as you do too :D