Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

I broke my blade guard on my Grizzly 1023

Posts

I broke my blade guard on my Grizzly 1023

#1

I broke my blade guard on my Grizzly 1023

David C. Lykins - Dallas GA

Today while cross cutting some 5" x 3" strips blocks of 1/2 plywood on my 1023S Grizzly, one of them got sideways popped up and shattered my plastic blade guard. So I called Grizzly to see if the new blade guard would fit my older 1023S but they indicated it wouldn't, though looking after the PDF file on their site I'm not sure why it wouldn't fit. So, I'm thinking of makeing a blade guard for the saw out of 1/4" Lexan or something similar.

I thought I'd get some ideas from you guys as to whether or not I should make a new blade guard or go buy one.

Also, I have a novice question, while ripping the plywood I did notice some tearout. If I made or purchased a "0-clearance" table saw insert, would this help to eliminate the tearout?

As usual, any help and advice is GREATLY appreciated.

Thanks!

Re: I broke my blade guard on my Grizzly 1023

#2

Leo Cuellar

Zero clearance insert, Yes!

Leo Cuellar

Would help greatly for tearout issues, David. A good quality task specific blade will help a lot also. Although a Freud Diablo "combination" are a pretty good blade if you are cash impaired like most of us these days.

Re: I broke my blade guard on my Grizzly 1023

#3

Re: Zero clearance insert, Yes!

Don Evans

I will not say you should NOT make one BUT I don't know if a glued or screwed together one will have the same safety quality a purchased one will. The purchase one is one molded unit of plastic which makes it stronger.

On the zero insert that depends. It is very hard to get one absolutely flat with the top of the table so most end up with it very slightly below, this may leave .001 clearance below wood where the cut is being made, enough for splintering at bottom edge. Also plywood is worse for this problem. One thing you can do is put "blue" painters tape on the wood where the blade will run down the middle of it. That helps more than any thing other than having the right blade for the job and I'll agree 100 percent on the Freud blades. I finally settle on them many years ago and just don't look further when time to buy another one.

Don

Re: I broke my blade guard on my Grizzly 1023

#5

Re: DIY overarm blade guards ...

Larry in NW OHIO

I made one just like that and it works very well for me, and don`t need a blade guard. Larry

Re: I broke my blade guard on my Grizzly 1023

#6

Don't Forget A Splitter With Your Guard *LINK*

Robby Wright in San Marcos, CA

The splitter is probably the most important safety device on your tablesaw to prevent kickback. I use the Shark Guard splitters from Leeway Workshop. He makes them to order and the quality is very good. I was able to get just the thickness I wanted. He also makes the Shark Guard guard and dust collection hood.

Robby Wright


Shark Guard Splitters from Leeway Workshop

Re: I broke my blade guard on my Grizzly 1023

#7

Re: Don't Forget A Splitter With Your Guard

mdclor

I have one and agree that SharkGuards are a quality product. The only downside is that you might have a long wait to receive yours, maybe 2-3 months IIRC. :(

Re: I broke my blade guard on my Grizzly 1023

#8

Scoring the workpiece

AZ in Colorado Springs

You can also score the workpiece to prevent chipping. Use a strightedge and a sharp utility knife to score the cut line. Cut just to the waste side of the line, and any chipping should occur on the waste side of the cut. If you're going to use both pieces, make a second score line, offset by the width of the blade. It's a bit tedious to set up and you wouldn't want to do this on every cut, but it can be a big help.