Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Table Saw Repair? Or Replace? (long)

Posts

Table Saw Repair? Or Replace? (long)

#1

Table Saw Repair? Or Replace? (long)

Rick Lasita

I have a Powermatic 63A Artisan (the 64A replaced it shortly after) table saw that is going on 20+ years old. Cast iron tables, Vega fence, has serviced me well over the years, a good solid saw, but I discovered the other day when cutting some plywood that my blade is about 3/16" out of square. Not sure when this happened, I think over time I have adjusted the fence to compensate for this, but it shows up a lot on cross cuts of any length. I have tried to find parts for this saw in the past, there are none out there, and I looked in the manual to understand how to adjust the trunions, nothing there. I finished the cutting my project pieces on my Delta 14" band saw and that got me thinking. Should I try to get this saw realigned or just get rid of it, use my band saw, or, go out and purchase another table saw. Ripping on the band saw isn't an issue, I use a lot of hand tools and I have some nice x-cut hand saws. So knowing there are no shortage of opinions here on our forum, what would you do? Thanks.

Re: Table Saw Repair? Or Replace? (long)

#2

Re: Table Saw Repair? Or Replace? (long)

Barry Irby

I would try to repair it. I Googled Align Contractor Table Saw And got at least one result that shows how. Newwoodworker.com (I think) has and article on how to do it. The article calls for a dial indicator to measure the position of the blade. You can get a cheap but serviceable one at Harbor Freight. (I don't buy much from HF, but for something I would use rarely, I would.) Actually, when I did some set up stuff on my TS I went old school and used a Number 4 pencil fastened to a block. I blackened one tooth on the blade as a reference and then use the pencil so that it would just snick the tooth. (Snick being a musical term indicating I played this by ear. I was listening for the same sound front and rear.)

I don't think this is very hard to do except that it might require some acrobatics to get to the bolts.

You might also try looking at YouTube to see if there is a video on how to do it.

3/16 is a lot, if you are talking about the blade, font to rear and the slot in the table. But, assuming it was properly aligned as some point there should be enough adjustment to realign it. Assuming you didn't trow it out of the truck and tumble it down the interstate in between.

Re: Table Saw Repair? Or Replace? (long)

#3

Re: Table Saw Repair? Or Replace? (long)

Mark

Easy to spend someone else's money, but depending on the type of work you do, 3/16's out seems like a lot. If the trunnions can't be accurately adjusted to get the saw back into square.....I'd lose it.

Re: Table Saw Repair? Or Replace? (long)

#4

Re: Table Saw Repair? Or Replace? (long)

Bill Earl

That's a good solid saw. I'd be surprised if it could not be brought back into alignment. The trick on most contractor-style saws I've worked on is getting at the trunnion bolts. You'll probably need a long extension on your socket wrench. It usually takes a few iterations to get them dialed in. They always seem to move a bit when you re-tighten the bolts.

Then again. If you are looking for an excuse to buy a new machine... :D

Re: Table Saw Repair? Or Replace? (long)

#5

Re: Table Saw Repair? Or Replace? (long)

Larry in NW OHIO

Rick If that saw is anything like my Unisaw you should have bolts at each corner of your table top underneath that bolts it to the cabinet, if it`s a cabinet saw. If it`s a contractor saw then they are on the trunnions inside. Good Luck Larry

Re: Table Saw Repair? Or Replace? (long)

#6

JL

Amen

JL

To both. Just think - a shiny new cabinet saw or hybrid.....

Re: Table Saw Repair? Or Replace? (long)

#7

Re: Table Saw Repair? Or Replace? (long) *LINK*

George, Oxford, NC

Attached is the link for the 64A manual. The adjustment for blade to miter slot is in there. The procedure is the same for the 63 or the 64. I have the 64A and although a bear to tangle your arms into the right position, it can be done and will result in a great running saw.

George


64A Manual

Re: Table Saw Repair? Or Replace? (long)

#8

Dale Lenz

Sounds to me like...

Dale Lenz

you are wanting to get a new TS in the first place. So... tune-up your old saw, sell it and get you a new 66 or Uni.

Re: Table Saw Repair? Or Replace? (long)

#9

Re: Table Saw Repair? Or Replace? (long)

woodenleg

I have the 64A. The blade got out of alignment and my son and I unhooked the top from the stand, flipped over and aligned the top. Before we turned it back over, we cleaned and lubed everything. At the same time we added a router table on the right side of the saw. On mine the 30 inch fence rails ran past the cast iron table about 20 in. Good Luck and let us know what you decided. Dave

Re: Table Saw Repair? Or Replace? (long)

#10

Take a shot at adjusting it.

Bruce, a MN Galoot

I have an older Delta contractor's saw, and I'd be willing to bet the trunnions are similar.

The trunnions on my 40+ y.o. saw come in three pieces, front and back holder/guides and the blade carrier, and are held in place with four bolts. Take the table off, loosen the bolts, clean off the gears, lube them up. Turn the table right side up, align the saw blade with the slot and tighten the bolts. Swear a lot because nudges have to be excruciatingly little. I've done mine a few times, mostly when the gears need cleaning and lubing. Takes about an hour if you are slow.

OTOH, if you want a new saw, get one. But adjust the blade parallel to the slot first because it'll make selling it ever so much easier. You'll be able to tell the new owner that it works great, you're just upgrading ;)

Re: Table Saw Repair? Or Replace? (long)

#11

Re: Table Saw Repair? Or Replace? (long)

Robby Wright in San Marcos, CA

Rick - I would line it back up again. It isn't hard. Take the motor off, loosen the trunnion bolts, nudge things back into position and tighten them back up. A dial indicator on a sled that runs in the miter slot makes things easier. Put a dot on a blade and use that as the reference for measuring. I used a couple of small wedges to move the trunnions around. Leave the bolts snug, but not tight, so you can move things just a little. Pay attention to where the blade ends up in relation to the slot in your throat inserts. While you are at it, if the trunnion mounting bolts are hardware grade, replace them with some good grade 5 bolts and use loctite to secure them. It took me less than an hour to line up my Rockwell contractor's saw.

Robby Wright

Re: Table Saw Repair? Or Replace? (long)

#12

Re: Table Saw Repair? Or Replace? (long)

Lee Daley

That's like throwing out you wife of 30 years or you dog of 10 for getting old ;)

It has served you well, and deserves to at least get some attention. Yes the thought of a brand new 21 year old trophy wife does sound appealing, but she put up with you over several renovation projects (and the saw did too :) )

If your needs have changed and a more precise saw is needed, go ahead, buy a new one. But remember, it will feel different!. On the other hand the current generation of tools, in humble but nonetheless opinion, are built to last a few years and thrown away. Try to repair it, but don't spend the equivelent of one one level up

Re: Table Saw Repair? Or Replace? (long)

#13

Re: Table Saw Repair? Or Replace? (long)

FredD

Dial indicators are a multipurpose measuring device and while nice , I think are unnecessary to adjust Miter slots and Rip fences to the blade.

I use a 3/4" square steel bar ,18" long that was milled for me by a Machinist friend and fits snugly in the Miter slot .

Using a Combination square , set for a predetermined distance and when the Blade of the square touches front and back the same on the saw blade body , your done.

Same for the rip Fence.

FredD

Re: Table Saw Repair? Or Replace? (long)

#14

Jim DeLaney, Austintown, Ohio

Re: Table Saw Repair? definitely repair(realign)

Jim DeLaney, Austintown, Ohio

I had that same saw for many years (finally sold it and got a Shop Fox cabinet saw) and had to realign it pretty often. I finally figured out that cranking it over to cut bevels was causing it to go out of alignment. I never did figure out WHY it was doing that, but every time I tilted the blade more than about ten degrees, it would be out of alignment when I returned to 90�.

To realign it, look under the table. There are four bolts (about 8mm diameter) that hold the corners of the trunnions to the underside of the table. Loosen them and slide the whole assembly around until the blade is back in alignment, then carefully tighten the bolts again. You may have to do this several times, since tightening the bolts often throws the alignment off again. Trial and measure; trial and measure, until you get it right.

There are commercial aids available, called P.A.L.S. They cost around $25, and attach to the trunnion bolts. After installing them, you can make the adjustments with an Allen wrench, which vastly simplifies the alignment procedure. If you go looking for the P.A.L.S., you�ll want the set for the Jet contractor�s saw. They don�t advertise any for the PM63. Woodcraft used to carry them � they still might.

Re: Table Saw Repair? Or Replace? (long)

#15

Re: Table Saw Repair? Or Replace? (long)

Rick Lasita

Thanks everyone for your input, overwhelming response is give it a realignment and see what happens. Who knows, maybe it will last another 20 years or so. Thanks again, I will give it a shot tomorrow and let you guys know how it comes out.

Re: Table Saw Repair? Or Replace? (long)

#16

Re: Table Saw Repair? Or Replace? (long)

Chuck Lenz

Sounds like you need a set of PALS from Inline Idustries for around $20 plus shipping to make the adjustment easier and more permanent. If you get rid of the saw, the only American made Table Saw out there now is the newer Delta Unisaw at the tune of around $3,000.

Re: Table Saw Repair? Or Replace? (long)

#17

Re: Table Saw Repair? definitely repair(realign)

Larry in NW OHIO

Jim I had a Craftsman contractors saw and always had trouble with that also, tilting and it would go out of alinment. I think I fianally figured it out. I think the motor hanging out the back would do it. All that weight and it hangs out the back and when it tilts and the motor goes up it puts more presure on the mounts and pushes on them and causes them to go out. At least that sounds good to me. Larry

Re: Table Saw Repair? Or Replace? (long)

#18

Jim DeLaney, Austintown, Ohio

Re: Table Saw Repair? definitely repair(realign)

Jim DeLaney, Austintown, Ohio

That may have been the cause, Larry. It was likely compounded by vibration, over time, possibly loosening the trunion bolts just a bit. I dunno. I sold the saw before I ever figured out the solution.