Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Help! Bit stuck in drill.

Posts

Help! Bit stuck in drill.

#1

Help!  Bit stuck in drill.

Scott in Montana

Hello all,

I have one of the small 12 volt or more correctly 10.8 volt Bosch drills. I was doing a bit of light duty drilling Friday and left the 3/8" bit in the chuck. Today I went out to clean up the shop and I can't get the bit out of the chuck. The keyless chuck just won't turn.

Any tricks or suggestions?

Thanks,

Scott in Montana

Re: Help! Bit stuck in drill.

#2

Re: Help!  Bit stuck in drill.

Lee Daley

Only the remedy from time immemorial, Liguid Wrench and Patience. And maybe a gentle bit of help with a pair of channel locks, the one on the rubber coat being padded with a scrap of leather or cloth. Or brute force involving large vise-grips, machinists vises, heavy hammers, foul language and the secure knowledge, that if it breaks, it was already broken.

Re: Help! Bit stuck in drill.

#3

Re: Help!  Bit stuck in drill.

Frank Grambo

Happened to me once. $200 Panasonic drill I got at a show. That 3/8" hole was the last it ever drilled. Should have kept it around just for 3/8" holes. It would have been a real novelty.

FFG

Re: Help! Bit stuck in drill.

#4

Re: Help!  Bit stuck in drill.

Joseph Mulherin, Sr

Scott, would it be possible to remove the chuck and tap the drill bit out from the other side?

Re: Help! Bit stuck in drill.

#5

Not likely

Keith Newton----Little Rock, Arkansas

The typical thread of the screw in the back of the jaws of a chuck is left hand thread, while the chuck itself is right hand thread, so until the bit is out, there is no way of getting to that screw.

I would try to grip the outside of the chuck with something like small vice-grips, and give it a quick tap with a light hammer, or mallet.

When I was a young carpenter, I could drive 16's all day long with one stroke, but I have never pushed a 16d nail into wood with a slow steady motion.

Re: Help! Bit stuck in drill.

#6

Re: Help!  Bit stuck in drill.

Phil Joines

I've had this happen on an old Makita corded. I used two water pump pliers to open the chuck. Just don't squeeze too hard. Then add a couple drops of oil.

Re: Help! Bit stuck in drill.

#7

Re: Help!  Bit stuck in drill.

Barry Irby

How about a strap wrench and a sharp rap with a hammer?

Re: Help! Bit stuck in drill.

#8

Something to try!

Lee Schierer McKean, PA

You may need to increase your grip. Get a couple of hose clamps and put them around the two portions of the chuck and tighten them both snugly. This should apply even pressure to the grip without damaging it. You can also increase your leverage with a pair of Channellocks against the screw on the clamp.

Lee

Re: Help! Bit stuck in drill.

#9

Re: Help!  Bit stuck in drill.

Rick in Colgate, Wi

Try tapping the chuck jaws down, use a blunt chisel and try and tap them back in a bit to relieve tension on the drill bit.

Re: Help! Bit stuck in drill.

#10

We'll give it a try!

Scott in Montana

Thanks for all of the input. I'll give it a try this morning. The rubberized chuck is proving to be more of a hassle than a benefit.

Scott in Montana

Re: Help! Bit stuck in drill.

#11

Tap tap tap

Grant in Iowa

Hi Scott,

Thinking about how the chuck works, we know that the three jaws holding the bit move forwards as they tighten. Stands to reason that a light tap on the end of each of those jaws with a small punch might help them let go. Direct the force of the tap towards the drill. I wouldn't advocate hitting very hard on a light duty drill this way, but it might jar things enough to let you loosen the chuck.

Might want to also note that it can be a bad idea to fully insert a bit in a drill chuck until it bottoms out. This can make them hard to remove. A similar thing happens on router collets as well.

FWIW,

Grant in Iowa