General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Friar 12/10/12, 8:18 PM
3 Replies · 54 ViewsLast post 12/11/12, 6:09 PM by Dick Coers -
by Merle 12/5/12, 2:00 AM
17 Replies · 20 ViewsLast post 12/11/12, 2:30 PM by Don Orr -
by Barry Irby 12/8/12, 2:00 AM
12 Replies · 16 ViewsLast post 12/11/12, 12:58 AM by Gary Smyth -
by don stephan 12/9/12, 12:55 AM
9 Replies · 51 ViewsLast post 12/10/12, 11:22 PM by David C. Lykins -
Jet Drum Sander Failed Mother Board Controller
by Dick Stariha 12/6/12, 1:40 AM
8 Replies · 24 ViewsLast post 12/10/12, 7:46 PM by Bob -
Very Super Cool Table Saw Fence...
by Derek Arita 12/7/12, 4:25 AM
14 Replies · 27 ViewsLast post 12/10/12, 7:20 PM by John in NM -
Might be the wrong forum for this...
by doug f 12/6/12, 2:11 AM
10 Replies · 44 ViewsLast post 12/10/12, 4:36 PM by Keith Newton -
by Dustmaker Mike 12/3/12, 9:13 PM
29 Replies · 72 ViewsLast post 12/10/12, 2:34 PM by John McGaw (Bodger) -
by Lee Gordon 12/8/12, 7:42 AM
4 Replies · 13 ViewsLast post 12/10/12, 1:00 AM by Ellis Walentine -
Perhaps a weather related question or two
by Barry Irby 12/8/12, 2:20 AM
4 Replies · 24 ViewsLast post 12/8/12, 9:02 PM by Yonak -
by Jerry Gibbs 12/7/12, 7:14 PM
5 Replies · 25 ViewsLast post 12/8/12, 1:52 AM by Jerry Gibbs -
Rigid 12v Lithium ion pack died...
by Dick Coers 12/5/12, 2:39 AM
7 Replies · 84 ViewsLast post 12/7/12, 4:04 AM by Bob -
OT - Hot water heater - possibly going
by JL 12/4/12, 8:49 PM
8 Replies · 30 ViewsLast post 12/6/12, 2:45 PM by JL -
by Clementine 12/6/12, 2:38 AM
4 Replies · 24 ViewsLast post 12/6/12, 1:13 PM by Clementine -
by Robert Hayward 12/3/12, 2:19 AM
11 Replies · 38 ViewsLast post 12/6/12, 3:00 AM by Robert Hayward -
by larry in nw ohio 12/5/12, 5:51 PM
3 Replies · 26 ViewsLast post 12/6/12, 12:23 AM by Jerry Nicholson -
by Richard Krieger 12/3/12, 2:53 AM
9 Replies · 20 ViewsLast post 12/5/12, 5:21 PM by Richard Krieger -
OT Stripping wall paper question
by Barry Irby 12/1/12, 1:44 AM
13 Replies · 36 ViewsLast post 12/5/12, 4:47 PM by Joseph Mulherin, sr -
by Robert Tutsky 12/4/12, 11:54 PM
10 Replies · 73 ViewsLast post 12/5/12, 3:33 PM by John McGaw (Bodger) -
I knew Unisaws held their value, but... *LINK*
by Dick Coers 12/2/12, 3:22 AM
5 Replies · 16 ViewsLast post 12/5/12, 1:21 PM by roger lance -
by Dave Bair 12/1/12, 5:25 PM
14 Replies · 53 ViewsLast post 12/5/12, 2:15 AM by Joseph Mulherin, sr -
Source for cartridge filter for cyclone?
by JL 12/3/12, 12:35 PM
15 Replies · 60 ViewsLast post 12/4/12, 11:21 PM by Bill Tindall, E.TN. -
by Ellis Walentine 12/2/12, 4:18 AM
19 Replies · 37 ViewsLast post 12/4/12, 10:11 PM by Barry Irby -
by Jerry Gibbs 12/4/12, 12:36 AM
13 Replies · 18 ViewsLast post 12/4/12, 4:48 PM by del schisler -
Tuesday Night Hand Tool Chat - Hide Glue
by Stephen Shepherd 12/4/12, 4:21 PM
0 Replies · 19 ViewsLast post 12/4/12, 4:21 PM by Stephen Shepherd -
by Matt Robinette 12/3/12, 8:04 PM
1 Reply · 20 ViewsLast post 12/4/12, 10:24 AM by Philip Duffy -
by Dick Stariha 12/2/12, 11:19 PM
3 Replies · 20 ViewsLast post 12/4/12, 1:57 AM by John McGaw (Bodger) -
Larvae (or something) in the ash
by JL 12/1/12, 1:41 PM
5 Replies · 38 ViewsLast post 12/3/12, 11:22 PM by Bill Tindall, E.TN. -
by Derek Arita 12/1/12, 4:33 PM
5 Replies · 18 ViewsLast post 12/3/12, 3:38 PM by Derek Arita -
WC Weekend Accomplishments.....
by Dennis E Peacock 12/3/12, 2:54 PM
1 Reply · 17 ViewsLast post 12/3/12, 3:26 PM by Tom Dunlap



