Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Very Super Cool Table Saw Fence...

Posts

Very Super Cool Table Saw Fence...

#1

Very Super Cool Table Saw Fence...

Derek Arita

Any have or are familiar with the Very Super Cool Tools table saw fence? Saw the Wood Whisperer do a little vid on them, so I took a look at the web site. Looks really neat. It's supposed to be dead flat, adjustable and versatile. I'd love to hear some feedback from someone who uses one.

Re: Very Super Cool Table Saw Fence...

#2

Bob

Re: Very Super Cool Table Saw Fence...

Bob

Post the link so we can see it?

Re: Very Super Cool Table Saw Fence...

#3

Re: Very Super Cool Table Saw Fence...

Derek Arita

http://vsctools.com/

The one thing I've tried to eliminate in my Biesemeyer Fence are the undulations that occur at every attachment screw of fence face to fence tube. It is slight, but enough to cause blade marks in the workpiece. From what the Wood Whisperer says, this fence is dead flat, with no deflection.

Re: Very Super Cool Table Saw Fence...

#4

Bob

Re: Very Super Cool Table Saw Fence...

Bob

OH Yea I remember when the "AskWoodMan" Allen built the fence. It does seem to be a good product invented out of necessity by a wood worker. I think it can be build a lot less expensive yourself using and existing Biesemeyer fence and extruded aluminum.

Re: Very Super Cool Table Saw Fence...

#5

Re: Very Super Cool Table Saw Fence...

Derek Arita

Tell me how. I've got two Bies type fences to play with.

Re: Very Super Cool Table Saw Fence...

#6

Re: Very Super Cool Table Saw Fence... *LINK*

Lee Schierer McKean, PA

Take a look at the 80/20 aluminum extrusions. They come in various lengths. You probably can buy a 2' piece for far less than the cost of the fence from this company. If supported by your beismeyer fence they should stay flat. Aluminum, even these heavy extrusions will deflect when pressure is applied, about 3 times more than steel.

Lee


Aluminum extrusions

Re: Very Super Cool Table Saw Fence...

#7

Here is the link *LINK*

John Lucas

I just purchases a used Grizzly cabinet makers saw and it came with only the large fence rails. Will not fit in my shop so I need to make a shorter one. I also don't like the fence very well. I'm going to look this over very hard. I can probably build one from scratch but the price of his fence seems very reasonable. I will do more research on it since I won't get around to doing anything with my saw until after Christmas.


http://vsctools.com/

Re: Very Super Cool Table Saw Fence...

#8

A contrarian view of table saw fences

Bill Tindall

I don't fine the "accuracy & precision" of a table saw fence very important. More important is how easy it is to get on and off the saw, adjust in tiny smidgens for wider or narrower, and fasten auxiliary stuff and clamps to it. To that end I am completely satisfied with the stock fence that came on my ancient Delta table saw. It has a bit of a bow in its middle and it probably is not perfectly in line with either the blade or the table slot (haven't checked it in years) but I don't find either to be an issue of any importance for ripping boards for furniture parts. An extruded fence would offer no "accuracy and precision" advantage I can think of yet result in two disadvantages.

Of great importance is the fact that my fence is relatively thin. Hence, I can readily screw auxiliary fences through the metal fence and indeed I have a whole stack of them near the saw for this or that specialty ripping situation where a sacrificial fence is required.

Additionally, for safety in ripping, the narrow fence rides in the space between my first an second fingers when ripping. My thumb propels the lumber forward and the first finger holds it down. With my hand locked to the fence there is no danger of it reaching the blade in some unanticipated event. I would not want to sacrifice this feature for one of the wide extruded fences.

Re: Very Super Cool Table Saw Fence...

#9

Looks neat, but...

John in NM

Is such a thing really necessary? Better to spend the $$$ on wood and do some building I think.

A table saw fence really only needs to be straight to half or a third of the length of the smallest piece that will be ripped, so if there is a little variation below say 3" intervals you won't notice any adverse effects. It may offend the eye, but practically speaking it simply doesn't matter.

I'm still using the original and somewhat awful fence on my 1950's saw. It's slower and not quite as easy to use as either a Biesmeyer or Unifence, but it works fine in terms of finished product. If I had lots of cash I would certainly replace it, but in reality it has simply never been much of a priority for me.

One thing that would impress me is if someone made a fence as simple and easy to manufacture as a Biesmeyer, yet made it adjustable while on the saw, like a Unifence. Making the adjustability in the fence rather than the locking mechanism is a poor compromise in my view, because it is not as sturdy.

Re: Very Super Cool Table Saw Fence...

#10

Re: Looks neat, but...

Alan in Little Washington (NC)

Funny you should ask. I'll say no more. :D

Re: Very Super Cool Table Saw Fence...

#11

Well, clearly some do think it necessary...

John in NM

Hence the success of Biesmeyer before he sold out to Delta. Nothing at all wrong with that, there's a market for nice fences. If these guys can make a living on their products, more power to them :D

The real trick is being able to price one's products significantly below the competition. If they could do that, in a few years Delta would probably buy them out too :D

Re: Very Super Cool Table Saw Fence...

#12

Re: Well, clearly some do think it necessary...

Alan in Little Washington (NC)

John, I was actually referring to the last paragraph in your previous post.

Someday you might see a fence that will satisfy most tablesaw (and router table) user requirements: A fence that is light weight but rugged and rock solid, has integral clamping T slots, has precision machined flat faces, allows easy, precise, and repeatable settings on both sides of the blade (or bit), has simple, integral micro adjustment capability in .001" increments (even when locked), slides easily, takes the same space as a standard T-square fence, can be quickly and easily removed, and has a single lever that quickly and securely locks both front AND rear of the fence- it won't slip unless hit with a sledge hammer. :)

Re: Very Super Cool Table Saw Fence...

#13

I must be missing something then

John in NM

I was only referring to the annoyance of adjusting a Biesmeyer for square, vs the long gone Unifence, which was super easy to adjust. That it rarely needs to be done is probably part of the reason no one has bothered to solve that one :D

Don't know about all that other stuff. Most of it isn't something I require from a fence. But if you could make one with even half those attributes for $50 less than the competition, you'd be set for life :D

Re: Very Super Cool Table Saw Fence...

#14

Re: I must be missing something then

Derek Arita

Just to let everyone know, he sells the T-Square alone. He encourages us to buy the just the T-Square, then go out and find what ever fence you want, to use with it. I was just on the ebay extrusion sight and there's a ton of stuff to use with the base T Square.

As for price, I think it's a fair price, considering the price of a Bies and other good fences. Remember, this is one guy, selling a few pieces, which probably cost a lot for him to produce. I like the fact that he's a "little guy", selling a new product that he came up with. It will be interesting for me to watch the progress of the product and I'll do my best to keep up with every new iteration. I wish I could come up with this kind of stuff. I wish I had that kind of creativity and fabrication abilities.

Re: Very Super Cool Table Saw Fence...

#15

Nothing wrong with the price really...

John in NM

It is in line or better than the Biesmeyer fence, depending on parts needed. Their advantage is really that you don't have to buy the complete system and can maybe save a bit that way.

I think its more that the hype on their website kind of turned me off a bit, because it strikes me they've traded the advantage of being able to use the extrusion for the disadvantage of losing the adjustment system that made both the Unifence and Beismeyer the market leaders in their times. Really I don't see their system as a huge improvement over a Beismeyer, just different, with different strengths and different weaknesses.

However, all this stuff did get me thinking, you could probably use an 80/20 extrusion for the guide rail and have a front adjusting t-square like the old Unifence for about the price they're charging. Then it really would be a big improvement over the Beismeyer styles.

I also started looking at Unifence parts on ebay, and realized that people were selling the same mediocre 1950's fence I have for $50-$150..... That's enough to make me think I should buy some surplus extrusions, weld together a t-square, and sell my fence to someone who wants an "original" saw over a useful one :D