Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Jointer upgrade or new

Posts

Jointer upgrade or new

#1

Jointer upgrade or new

Richard Krieger

I have a G1182 Grizzly 6" jointer about 18 years old. I'm interested in updating to a helical or spiral cutter head for it, but then am thinking maybe I should go the extra and step up to an 8" with the helical or spiral cutter. Does anyone own one of these units and can you offer any advice on making this decision? Any help would be greatly appreciated. Thanks in advance.

Re: Jointer upgrade or new

#2

Re: Jointer upgrade or new

Paul Blackwell

I had to downgrade from a Grizzly 8" jointer when we moved to a new place about 15 months ago. I bought a new 6" Grizzly jointer with the helical head and carbide inserts. I love it. It is the smoothest cutting jointer I have ever used. The cut is so smooth that little sanding is required.

Re: Jointer upgrade or new

#3

Joe Bradshaw

Re: Jointer upgrade or new

Joe Bradshaw

I really like my 6" Griz with the helical head. I mainly use it to get a 90 degree corner on box blanks.

Re: Jointer upgrade or new

#4

A question to you

Dustmaker Mike

How many times over the last 15 years have you said I wish I had an 8 inch jointer so could do XXX. If it is more often then not I would go with the 8 inch if not I would upgrade the 6 inch, but if ya just gota have it then go for it(-;

Re: Jointer upgrade or new

#5

JL

Ditto

JL

Have you ever felt that the 6" was inadequate to the work that you would like to do?

I bought an 8" years ago. Haven't regretted it - but I do long, heavy pieces of lumber. As an example, Friday I jointed and planed a 9/4 piece of ash that was 6" W x 8' long. I could have done it on a 6" - but it was much easier on an 8".

If you are jointing long, heavy pieces of lumber - an 8" would make sense.

Re: Jointer upgrade or new

#6

Re: Jointer upgrade or new

Joe in a Cleveland suburb

FWIW, I have a 6" Delta. Always wished I had bought an 8" one.

Re: Jointer upgrade or new

#7

Good advice

John in NM

I have an 8", but a lot of the time I'm jointing edges or face jointing rails and stuff smaller than 6". My habit is to rough out parts with the TS or BS, maybe 1/8" to 1/4" over width, then worry about flattening and squaring them up. I could easily make do with a 6" jointer for that kind of work.

Re: Jointer upgrade or new

#8

G0490X

Merle

I bought this model 4.5 years ago. I mostly work with qswo, some walnut, cherry, etc. I am still using the same faces on the cutter head inserts as the day it was delivered. I get no chip out, except maybe around a knot. It is also relatively quiet-I have left it running and couldn't hear it over the dust collector and head phones. I would buy it again.

http://www.grizzly.com/products/8-Jointer-w-Spiral-Cutterhead/G0490X

Re: Jointer upgrade or new

#9

Re: Jointer upgrade or new

Larry Clinton At Frankfort, (Central) Indiana

I had a 6" Grizzly joiner for several years, changed and sharpened cutters on it a few times. When I built my new shop I upgraded to the Grizzly 8" segmented cutter head (very similar to my Byrd head on my planer). I really appreciate the difference for several reasons, first the finish of the carbide spiral head is far superior to the old cutters. Second the extra length of the beds make it much easier to straighten long boards. Third the 8" width does come in real handy when working with some of the stock I have. The motor is also larger so you can take a deeper cut when you wish. I really am glad I did purchase of the 8" rather than upgrade the 6".

Re: Jointer upgrade or new

#10

Re: Jointer upgrade or new

Richard Krieger

THANK YOU!!

All good advice and tips. Still haven't decided, am leaning towards the 8".

Merry CHRISTmas!!