Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Help with oversize pin hole

Posts

Help with oversize pin hole

#1

Robert Tutsky

Help with oversize pin hole

Robert Tutsky

I have a Skil 4 x 36 inch belt sander. Now and then I use the 6" side circular sander disk. Problem is with the adjustable table that is attached to the machine. It adjusts from level to 45 degrees for guiding stock through the sander. The pin that rotates in the hole for adjustment is incredibly sloppy. It isn't worn but was manufactured with too large of a hole from the beginning. No matter how tight I try to get the knob to lock the table it moves at least 5 degrees off level when sanding. My thought was to fill the hole with JB Steel Reinforced Epoxy then re-drill the hole to the correct size diameter. Question is, do you think this would work long term or do you have a better idea? Thanks in advance for your help.

Re: Help with oversize pin hole

#2

Re: Help with oversize pin hole

Galen Vetterick

Not sure of the setup you are dealing with but can you put a sleeve over the pin if it cannot be replaced with a larger diameter pin. Can you press a sleeve into the hole to match the pin? Rather than epoxy I'd opt for even drilling the hole more oversized so a standard sleeve bushing or bronze bearing would fit.

Re: Help with oversize pin hole

#3

Re: Help with oversize pin hole

Bill Houghton, Sebastopol, CA

Your hardware store may have - should have, if they're any good - brass/bronze bushings in various sizes. If not them, a bearing house. The trick will be boring out the hole accurately. If you've got a drill press, think long and hard about how to jig it so you can bore out the hole.

Bushings come in two sorts: solid brass/bronze, on which the holes are usually undersized to allow for reaming to size, and oilite, on which the holes are usually sized to true diameters (plus a little clearance). Either one would work in this application. The solid ones might give you some wiggle room for getting the hole properly aligned - bore, install, re-bore to fit.

Have a look at the pin, too, and if it's worn, think about how to replace it.

Re: Help with oversize pin hole

#4

Robert Tutsky

Sleeve/bearing option...

Robert Tutsky

Thanks Galen for the idea. I think it's a better option than what I came up with. A sleeve over the pin wouldn't work because ironically the pin fits perfectly in another hole if the table is used with the belt version (adjusted vertically) of the sander (go figure). But a sleeve inserted into the over sized hole would be a permanent solution. Now to see if I can locate a sleeve or a bronze bar that I can drill to size.

On another note... where is the quality control on some of the tools produced today? It's an obvious gross manufacturing error. I bought this new and would have sent it back but I needed a belt sander for a project and used it over a couple of days and would have felt uncomfortable sending it back after using it.

Re: Help with oversize pin hole

#5

Robert Tutsky

Re: Help with oversize pin hole

Robert Tutsky

Bill thanks for the return. The pin is fine. Since the machine is new it hasn't had much use and most of the sanding is 90 degrees to the disc anyway so I don't imagine changing the table angle much, I just don't want the table to move while sanding. I have a drill press so boring out for a sleeve shouldn't be a problem. I am going to check out online suppliers (MSG, Enco, McMaster-Carr, etc.). I am quite resourceful and it will be fixed but this problem shouldn't have existed from the get go.

Re: Help with oversize pin hole

#6

Re: Sleeve/bearing option...

Galen Vetterick

You are not talking much load at all so nylon will last even if thin wall. Don't overlook those in Lowes, Menards , ACE hardware. They mostly have thicker walls but in my case on a wood lathe you can turn or bore about anything you need in nylon or bronze. Make sure you use a good v-block to clamp the material if you change the ID on a drill press.

Heck, I've even used nylon toggle anchors bodies for nylon bearings.

Re: Help with oversize pin hole

#7

Ellis Walentine

Hobbyist tools

Ellis Walentine

I've observed that manufacturers skimp on engineering features on smaller-scale and lower-end tools, not to mention production quality, and 4 x 36 is pretty small. They need to keep prices down by using low-tech components like this quadrant system.

If you're crafty, you can usually come up with shop-made solutions that will greatly outperform the original arrangement. Is there a home-baked solution?

Trade offs.......

Ellis

Re: Help with oversize pin hole

#8

Robert Tutsky

Re: Hobbyist tools

Robert Tutsky

A shop made solution wouldn't be a problem for me to construct but at the moment I do have this machine, I turn it on and it spins/moves sandpaper that sands wood, I just need more accuracy. I realize it's small size but I am using it for sanding small parts anyway. I had a 6 x 48 Delta at one point and loved it, although even then I was usually sanding small parts. I will fix this machine to make it work the way I need it to.

Re: Help with oversize pin hole

#9

Re: Hobbyist tools

Jesse Cloud

Skil used to make good products. Now it is the off brand for Bosch, aimed at people who don't particularly care about quality - which doesn't sound like you.

I suspect that if you fix the pin, there will still be other problems with the tool.

I would be thinking seriously about cutting my losses on this piece and replacing it with a quality tool.

Re: Help with oversize pin hole

#10

Robert Tutsky

I have to agree with you...

Robert Tutsky

I will use this tool for all it's worth but at the same time I will be targeting a product that will give me better service. Thanks for your remarks. It helps.

Re: Help with oversize pin hole

#11

Re: Help with oversize pin hole

John McGaw (Bodger)

As I read it, your problem is that the hole is too big for the pin and that the pin is the pivot point. Clearly the hole must be made smaller or the pin must be made larger. If it was close and the metal was amenable then one might "punch" the metal around the pin -- this is a (temporary) solution used in clock repair when brass plates wear and gears start to wobble on their shafts. Alternatively, one might drill the hole and install a sleeve into it which fits the pin (also used in clock repair) or one might remove the pin and install a larger one which fits the hole or do both. Any of these is relatively simple although having a broach of the proper size would assist in any hole fitting.