Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Jet Drum Sander Failed Mother Board Controller

Posts

Jet Drum Sander Failed Mother Board Controller

#1

Jet Drum Sander  Failed Mother Board   Controller

Dick Stariha


Jet drum Sander 21/42 smokin mother board (now toast). New replacement part is over $100.00

Can it be rewired to control the two motors direct. They both have on off switches.

I never thought that the controller that adjusted the belt speed was effective anyway.

DS

Re: Jet Drum Sander Failed Mother Board Controller

#2

Bob

Re: Jet Drum Sander  Failed Mother Board   Control

Bob

I never noticed that the speed control ever worked I think you would loose the var/speed if you wired it direct. I would look at replacing the component from a 3rd party supplier. But without the board and DBD drawings it would be hard to troubleshoot an make it work the way it should.

Re: Jet Drum Sander Failed Mother Board Controller

#3

Re: Jet Drum Sander  Failed Mother Board   Control

Jerry Roberts

Sometimes companys offer rebuilt mother boards. I replaced one in my wifes exercise walker for about half the price and it worked ok. Dont know abt Jet tho.

Re: Jet Drum Sander Failed Mother Board Controller

#4

Re: Jet Drum Sander  Failed Mother Board   Control

Alan in Little Washington (NC)

Unless you know what you are doing I would avoid rewiring the conveyor motor. i can't say for sure, but that "mother board" is probably a DC controller- it rectifies the AC to DC to power a DC conveyor motor. If so, you can't run the conveyor motor on AC.

Re: Jet Drum Sander Failed Mother Board Controller

#5

Re: Jet Drum Sander  Failed Mother Board   Control

Dick Stariha

Alan,

Thank you for your reply. ------->

"Unless you know what you are doing I would avoid rewiring the conveyor motor. i can't say for sure, but that "mother board" is probably a DC controller- it rectifies the AC to DC to power a DC conveyor motor. If so, you can't run the conveyor motor on AC."

Can any one out there say "for sure"if the "mother board" has a rectifying function? Can any one supply a schematic? Or is that a proprietary secret?

Best regards,

DS

Re: Jet Drum Sander Failed Mother Board Controller

#6

Re: Jet Drum Sander  Failed Mother Board   Control

Alan in Little Washington (NC)

Are you sure you don't have a jet 22/44? Here is the info straight from a Jet 22/44 Pro document:

"The conveyor belt is driven by a separate 1/30 HP DC motor."

A write-up on NewWoodworker dot com about the 22/44OSC says: "The conveyor belt is powered by separate 43 inch-lb DC motor. This DC motor was selected in part to support variable speed and a special bit of protective technology described in the conveyor section below."

"Using the DC motor to power the JET 22-44OSC Oscillating Drum Sander conveyor belt clears the way for variable speed. However, JET also developed their patented SandSmart™ technology that works with the variable speed control. The infinitely variable speed control produces feed rates from 0 to 10 feet per minute. That lets the operator choose the best rate for the job at hand.

The SandSmart™ technology monitors the load on the conveyor belt. When that load exceeds its built-in limits, the SandSmart™ circuitry automatically reduces the feed rate to a slower rate as long as is needed. When the load is relieved, the original feed rate is restored. An LED light next to the speed control dial comes on when the SandSmart™ system has taken over."

From the Jet 16/32 manual: "Conveyor Motor: 43in/lb. torque, direct drive D.C. motor, infinitely variable rate of 0-10'/minute."

I think you can safely assume your "mother board" is a DC controller (which means is has an inverter inside) and the motor is a DC gear motor.

I have seen a lot of reports about failed conveyor motors. Found this comment from 2009:

"PS, I ended up needing another speed control too, since it cooked as soon as I turned it on and I finally found one at KB controls.com, Pt# KBVC-14. Surprisingly reasonable."

Re: Jet Drum Sander Failed Mother Board Controller

#7

Re: Jet Drum Sander  Failed Mother Board   Control

Dick Stariha

Thanks again ,Alan for your follow up reply. Yes , my machine is a 22/44 model( got mixed up on my #'s)

Hey. You're dealing with a senior citizen here.LOL

I'm going to reply to that KB site . You may have saved my bacon.---> at KB controls.com, Pt# KBVC-14. Surprisingly reasonable

Gratia ( a little Spanish lingo there)

DS

Re: Jet Drum Sander Failed Mother Board Controller

#8

Try the reset button first...

Grant in Iowa

Many owners of drum sanders miss that there's a reset switch. On some models it is a small hole requiring a paperclip or similar object to push the button. On other models it is an actual reset switch.

Sounds like yours is visibly smoked, but thought I'd mention it in case you meant metaphorically smoked...

FWIW,

Grant in Iowa

Re: Jet Drum Sander Failed Mother Board Controller

#9

Bob

Re: Jet Drum Sander  Failed Mother Board   Control

Bob

I have the 22/44 but never noticed that there was any type of protection to slow down the conveyor. In fact it would just burn up the paper and the board being sanded if I tried to take to big of a bite. Do all the 22/44s have this? I think I remember reading mind does but never saw it in action so I just take a lot of light passes. I did however found I can get better results with my hand plane and orbital sander.