Hand Tools
Traditional tools, sharpening, restoration, usage techniques.
Related: Hand Tools archive
Topic list
-
TopicStatisticsLast post
-
OT - sigh...another round tuit
by Bill Houghton, sun/cold in Sebastopol, CA 12/20/08, 11:26 PM
5 Replies · 46 ViewsLast post 12/21/08, 2:15 AM by steve mackay -
by steve mackay 12/20/08, 1:40 AM
4 Replies · 25 ViewsLast post 12/20/08, 10:36 PM by Todd O. Cronkhite Maine Native, Presently Away -
Wayne Anderson small A4 plane, NEW Ebony infill on
by Mark Swanson 12/20/08, 7:00 PM
1 Reply · 18 ViewsLast post 12/20/08, 8:08 PM by Wiley Horne - S. CA -
by Ben Retzinger 12/20/08, 3:25 PM
3 Replies · 96 ViewsLast post 12/20/08, 7:12 PM by Ben Retzinger -
by Wiley Horne - S. CA 12/17/08, 8:35 PM
20 Replies · 77 ViewsLast post 12/19/08, 7:49 PM by Pam Niedermayer, Austin, TX -
by Todd Hughes 12/16/08, 10:58 AM
19 Replies · 82 ViewsLast post 12/19/08, 2:51 PM by Todd O. Cronkhite Maine Native, Presently Away -
Milling Osage, Or While my chainsaw gently weeps
by Dominic in Buck's County PA 12/15/08, 3:41 AM
11 Replies · 72 ViewsLast post 12/19/08, 12:42 PM by Dominic in Bucks County PA -
by Pam Niedermayer, Austin, TX 12/17/08, 6:47 AM
8 Replies · 33 ViewsLast post 12/19/08, 2:51 AM by Scott Burr in Ben Lomond, CA -
*** Stanley #45 at Auction *** *LINK*
by Ellis Walentine 12/18/08, 4:23 PM
0 Replies · 33 ViewsLast post 12/18/08, 4:23 PM by Ellis Walentine -
by Denis Ch�nard, Orl�ans, Ont. 12/17/08, 12:23 AM
1 Reply · 31 ViewsLast post 12/18/08, 5:40 AM by Scott Burr in Ben Lomond, CA -
by Rich S 12/15/08, 9:22 PM
7 Replies · 640 ViewsLast post 12/18/08, 5:24 AM by Pat Riley -
by Todd O. Cronkhite Maine Native, Presently Away 12/15/08, 7:48 PM
9 Replies · 30 ViewsLast post 12/17/08, 11:34 AM by Todd Hughes -
by Dan Mitchell 12/16/08, 4:53 AM
2 Replies · 142 ViewsLast post 12/17/08, 4:29 AM by Scott Burr in Ben Lomond, CA -
by steve mackay 12/14/08, 10:01 PM
7 Replies · 62 ViewsLast post 12/17/08, 4:19 AM by Scott Burr in Ben Lomond, CA -
first dovetails...last dovetails?
by Gary 12/15/08, 2:15 PM
18 Replies · 42 ViewsLast post 12/16/08, 6:46 PM by Glenn Madsen near San Francisco -
by Stephen Shepherd in the State of Deseret 12/16/08, 3:22 PM
0 Replies · 32 ViewsLast post 12/16/08, 3:22 PM by Stephen Shepherd in the State of Deseret -
So, how come no one's mentioned this until now? *LINK*
by Bill Houghton, getting sunny in Sebastopol, CA 12/13/08, 1:28 AM
6 Replies · 30 ViewsLast post 12/16/08, 1:50 AM by Scott Burr in Ben Lomond, CA -
Richard Neve had it right in 1736 2 3
by Larry Williams 11/29/08, 1:21 AM
59 Replies · 353 ViewsLast post 12/14/08, 8:10 PM by Stephen Shepherd in the State of Deseret -
by Henry Allsworth 12/9/08, 6:39 PM
11 Replies · 298 ViewsLast post 12/14/08, 5:44 AM by Michael Brady -
by Edward in Vancouver 12/10/08, 5:37 AM
4 Replies · 35 ViewsLast post 12/13/08, 2:54 PM by James Watriss -
by David Miller 12/10/08, 2:45 PM
5 Replies · 56 ViewsLast post 12/12/08, 12:09 AM by David Miller -
by roninkokomo 12/9/08, 1:37 PM
11 Replies · 23 ViewsLast post 12/11/08, 10:24 PM by Bill Houghton, overcast Sebastopol, CA again -
Bid deadlines on Benefits Auction tool auctions
by Bill Houghton, getting sunny in Sebastopol, CA 12/11/08, 1:31 PM
0 Replies · 48 ViewsLast post 12/11/08, 1:31 PM by Bill Houghton, getting sunny in Sebastopol, CA -
by Ellis Walentine 12/10/08, 1:48 PM
1 Reply · 18 ViewsLast post 12/11/08, 2:13 AM by Wiley Horne - S. CA -
by john lucas 12/10/08, 1:36 AM
9 Replies · 90 ViewsLast post 12/10/08, 5:32 PM by paul womack -
by David Miller form Iowa 12/7/08, 2:51 PM
4 Replies · 21 ViewsLast post 12/10/08, 6:55 AM by Scott Burr in Ben Lomond, CA -
OT: Forging I mentioned in saw post
by Dean Lapinel 12/6/08, 7:53 PM
18 Replies · 57 ViewsLast post 12/10/08, 12:48 AM by John in NM -
by Doug Reynolds 12/2/08, 10:44 PM
65 Replies · 227 ViewsLast post 12/9/08, 5:53 PM by Dave Anderson NH -
by Stephen Shepherd in the State of Deseret 12/9/08, 2:58 PM
0 Replies · 18 ViewsLast post 12/9/08, 2:58 PM by Stephen Shepherd in the State of Deseret -
by tek,brunswick 12/5/08, 5:37 PM
11 Replies · 37 ViewsLast post 12/9/08, 2:54 PM by Ernie Miller



