Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

So, how come no one's mentioned this until now? *LINK*

Posts

So, how come no one's mentioned this until now? *LINK*

#1

So, how come no one's mentioned this until now? *LINK*

Bill Houghton, getting sunny in Sebastopol, CA

>Lee Valley sure rethinks tools in an interesting way. If I didn't already have a Stanley, I'd be considering this - very good price.


Beady little tool

Re: So, how come no one's mentioned this until now? *LINK*

#2

Stanley, LV...

Scott Burr in Ben Lomond, CA

>I prefer my old Preston...

Not dissin' my 66 BTW.

Re: So, how come no one's mentioned this until now? *LINK*

#3

Re: So, how come no one's mentioned this until now

charlie belden

>Question:

Can't see how the Veritas beading tool reqisters the cutter to vertical. That's kind of important if you want to "cut" the whole profile since tilting will change the results.

Given that "setting it vertical" issue, having a fixed fence that requires that you move the cutter to the desired location would appear to require resetting the cutter vertically each time.

The LN beading tool solves both problems - and keeps your hands lower - and lower is better with this type of tool.

Wonder when H.N.T. Gordon will come out with a beading tool version of their shaves? Their "handles" get your hands right down on the work. Looks pretty plane - but works really well.

Re: So, how come no one's mentioned this until now? *LINK*

#4

Re: So, how come no one's mentioned this until now *LINK*

Derek Cohen (in Perth, Australia)

>Given that "setting it vertical" issue, having a fixed fence that requires that you move the cutter to the desired location would appear to require resetting the cutter vertically each time.

Hi Charlie

I would argue that this is unnecessary.

I mostly use scratch stocks (ala Hack). These use a fixed blade. In other words, set the blade once and that's it.

The Veritas (which arrived yesterday) indeed does not appear to have the vertical setting of the Stanley/LN #66 (I have the Stanley), but again I set the blade once, so depth of cut is not an issue, nor is the positioning against the fence. Set once and that is it.

The Veritas has a deeper fence (5/8") than the LN (3/8" - my Stanley has LN fences), and in my experience this is the more important feature for cutting a clean profile. Frankly, I would have liked to see a deeper fence, or some way of adding to the depth of the fence (which there is not), but the length of the fence (2 1/2") is a great improvement on the Stanley/LN versions (1 5/8") (see my mod in the link below).

Neither my scratch stocks nor my shopmade wooden beader have a way of setting a true vertical. I gauge this by eye. The woodie has a sliding fence, which helps a little. Eye is good enough.

If you want to reproduce a bead that has already been cut, place the blade in the cut profile and tighten the fence against the side of the board.

Regards from Perth

Derek


Improving the #66 Hand Beader

Re: So, how come no one's mentioned this until now? *LINK*

#5

preston range *LINK*

paul womack

>I prefer my old Preston...

Which one - they made LOTS of scratch tools...

BugBear


link to discussion

Re: So, how come no one's mentioned this until now? *LINK*

#6

OT - "link to discussion"

Dan Moening

>Paul,

All of the posts I have read of yours since last week have a "link to discussion" regarding Alfs vise racking shim device.

Is this somehow stuck in your response profile?

I don't think it's me as I tend to clear cookies, etc rather frequently.

Re: So, how come no one's mentioned this until now? *LINK*

#7

Yep appears to be a bad linkie. Please re-post

Scott Burr in Ben Lomond, CA

>