General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Mark Mandell 7/18/19, 8:53 PM
8 Replies · 33 ViewsLast post 7/20/19, 1:30 AM by Clint Searl -
How Would You Describe This Shingle?
by John W Foster 7/19/19, 7:28 PM
3 Replies · 21 ViewsLast post 7/20/19, 12:54 AM by Warren in Lancaster, PA -
by Bill Tindall, E.TN. 7/16/19, 9:43 PM
14 Replies · 50 ViewsLast post 7/19/19, 10:16 PM by Chuck Kettler -
Well after 12 yeasr in the Mountains of Cle
by Mike L 7/17/19, 11:24 AM
15 Replies · 72 ViewsLast post 7/19/19, 4:42 PM by MartinMJ -
Unique Yates American combination machine
by Dick Coers 7/18/19, 9:00 PM
0 Replies · 54 ViewsLast post 7/18/19, 9:00 PM by Dick Coers -
by Barry Irby 7/18/19, 7:03 PM
1 Reply · 30 ViewsLast post 7/18/19, 8:49 PM by Mark Mandell -
Derek - Bill dovetail challenge 2
by Derek Cohen (in Perth, Australia) 7/14/19, 4:11 PM
28 Replies · 106 ViewsLast post 7/18/19, 1:06 AM by Derek Cohen (in Perth, Australia) -
by Clint Searl 7/17/19, 12:47 AM
13 Replies · 55 ViewsLast post 7/18/19, 12:14 AM by Bill Tindall, E.TN. -
by William Duffield 7/16/19, 7:04 PM
4 Replies · 26 ViewsLast post 7/17/19, 4:02 PM by William Duffield -
by Thomas Skaggs 7/12/19, 3:21 PM
8 Replies · 38 ViewsLast post 7/17/19, 12:02 AM by Craig Daymon -
by Barry Irby 7/15/19, 11:59 AM
9 Replies · 75 ViewsLast post 7/16/19, 11:24 PM by John in NM -
by JL 7/14/19, 8:54 PM
9 Replies · 69 ViewsLast post 7/16/19, 6:03 PM by Jim Dillon -
What to do with an abundance of Sand Paper
by Barry Irby 7/13/19, 12:04 PM
8 Replies · 79 ViewsLast post 7/16/19, 5:20 PM by Barry Irby -
Cross between an MFT and a CNC? *LINK*
by Dick Coers 7/14/19, 3:37 AM
2 Replies · 31 ViewsLast post 7/15/19, 12:22 AM by Dick Coers -
by Grant In Iowa 7/12/19, 2:54 PM
1 Reply · 23 ViewsLast post 7/13/19, 2:57 PM by Barry Irby -
Quest for the perfect hinge mortise router-found
by Bill Tindall, E.TN. 7/10/19, 9:11 PM
5 Replies · 21 ViewsLast post 7/12/19, 5:55 PM by John in NM -
by McKay 7/9/19, 4:44 PM
17 Replies · 58 ViewsLast post 7/12/19, 4:55 PM by Keith Newton -
Finishes: Claims, Myths, and Questions
by Don Stephan 7/9/19, 12:21 AM
7 Replies · 51 ViewsLast post 7/12/19, 1:22 AM by AZ -
hinge installation, when all else fails
by Bill Tindall, E.TN. 7/9/19, 12:41 AM
13 Replies · 33 ViewsLast post 7/11/19, 11:09 AM by Barry Irby -
End user data on particle M4 plane iron *LINK*
by E Phillip Smith 7/11/19, 2:20 AM
0 Replies · 41 ViewsLast post 7/11/19, 2:20 AM by E Phillip Smith -
by Howard in Toronto 7/8/19, 11:21 PM
14 Replies · 34 ViewsLast post 7/11/19, 1:28 AM by Howard in Toronto -
by Buckaroo 7/7/19, 8:53 PM
11 Replies · 26 ViewsLast post 7/9/19, 7:55 PM by Thomas T Dunlap -
request router recommendation 2
by Bill Tindall, E.TN. 7/7/19, 2:25 PM
27 Replies · 141 ViewsLast post 7/9/19, 7:19 PM by Steve Elliott -
by del schisler 7/8/19, 3:24 PM
6 Replies · 30 ViewsLast post 7/9/19, 4:57 PM by david weaver -
by Jerry Gibbs 7/7/19, 7:39 PM
3 Replies · 27 ViewsLast post 7/9/19, 2:00 PM by William Duffield -
by McKay 7/9/19, 3:47 AM
2 Replies · 24 ViewsLast post 7/9/19, 1:26 PM by Kneale Brownson -
by Mark Mandell 7/6/19, 12:22 AM
9 Replies · 29 ViewsLast post 7/8/19, 11:54 PM by Kneale Brownson -
by Hank Knight 7/6/19, 5:02 PM
6 Replies · 37 ViewsLast post 7/8/19, 2:09 PM by Hank Knight -
by Michael van pelt 7/7/19, 12:51 PM
3 Replies · 28 ViewsLast post 7/8/19, 1:10 AM by Michael van pelt -
Stain blotching-continuing discussion
by Bill Tindall, E.TN. 7/7/19, 3:05 PM
2 Replies · 23 ViewsLast post 7/8/19, 12:49 AM by Ron in Sterling, CT