General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Derek Cohen (in Perth, Australia) 7/7/19, 4:11 PM
4 Replies · 24 ViewsLast post 7/8/19, 12:11 AM by Bill Tindall, E.TN. -
The Wiley Coyote of Ground hogs..... 2
by Barry Irby 7/3/19, 11:04 AM
29 Replies · 68 ViewsLast post 7/7/19, 9:53 PM by Buckaroo -
Band saw is vertically challenged 2
by Bill Tindall, E.TN. 6/27/19, 7:53 PM
28 Replies · 199 ViewsLast post 7/7/19, 9:50 PM by Bill Tindall, E.TN. -
Micro-adjust for router or almost anything *LINK*
by Craig Daymon 7/7/19, 8:52 PM
0 Replies · 96 ViewsLast post 7/7/19, 8:52 PM by Craig Daymon -
by Barry Irby 7/6/19, 3:04 PM
4 Replies · 29 ViewsLast post 7/7/19, 3:09 PM by John McGaw -
by Barry Irby 7/6/19, 3:09 PM
10 Replies · 53 ViewsLast post 7/7/19, 1:50 PM by Mark Mandell -
by Bill Tindall, E.TN. 7/6/19, 2:28 PM
0 Replies · 42 ViewsLast post 7/6/19, 2:28 PM by Bill Tindall, E.TN. -
by Michael van pelt 6/30/19, 10:02 PM
14 Replies · 47 ViewsLast post 7/5/19, 5:12 PM by John in NM -
by Bill Tindall, E.TN. 7/3/19, 3:10 PM
11 Replies · 45 ViewsLast post 7/4/19, 6:11 PM by Jim Dillon -
by Mark Mandell 7/2/19, 1:17 PM
13 Replies · 34 ViewsLast post 7/3/19, 11:58 PM by Mark Mandell -
Band saw cutting of a maple crotch
by Ed Wesolek 7/2/19, 4:19 PM
9 Replies · 28 ViewsLast post 7/3/19, 6:55 PM by John K Jordan -
by Dick Coers 6/28/19, 3:03 AM
23 Replies · 105 ViewsLast post 7/2/19, 4:13 AM by AZ -
by Jack Guzman from Maine 6/30/19, 4:16 PM
3 Replies · 22 ViewsLast post 7/2/19, 1:14 AM by Clint Searl -
Question on Kreg screws and Plugging the hole?
by Barry Irby 7/1/19, 1:10 PM
6 Replies · 60 ViewsLast post 7/1/19, 11:10 PM by John in NM -
by Kneale Brownson 7/1/19, 7:40 PM
2 Replies · 34 ViewsLast post 7/1/19, 11:00 PM by Kneale Brownson -
by JL 6/30/19, 6:29 PM
8 Replies · 25 ViewsLast post 7/1/19, 8:14 PM by John K Jordan -
Exasperated with Fine Woodworking Magazine!
by Derek Cohen (in Perth, Australia) 6/29/19, 3:49 PM
20 Replies · 56 ViewsLast post 7/1/19, 8:10 PM by david weaver -
The best way to make a frame and panel door
by Bill Tindall, E.TN. 6/30/19, 10:17 PM
4 Replies · 29 ViewsLast post 7/1/19, 7:40 PM by Sgian Dubh -
by Mark Mandell 6/30/19, 3:23 PM
9 Replies · 27 ViewsLast post 7/1/19, 5:11 PM by Garthinsandiego -
From Carol Reed's facebook page
by Alan Young 6/26/19, 10:47 PM
14 Replies · 48 ViewsLast post 7/1/19, 2:13 PM by Ellis Walentine -
Use a non-working fridge to store finishes
by Johanna 6/25/19, 7:34 PM
8 Replies · 31 ViewsLast post 6/30/19, 3:50 PM by William Duffield -
Cohen leg on Ruhlmann furniture, nearly
by Bill Tindall, E.TN. 6/28/19, 6:22 PM
8 Replies · 53 ViewsLast post 6/29/19, 11:33 PM by Bill Tindall, E.TN. -
by Barry Irby 6/29/19, 1:35 PM
3 Replies · 33 ViewsLast post 6/29/19, 9:30 PM by Jesse Cloud -
by Bill Tindall, E.TN. 6/23/19, 9:04 PM
18 Replies · 46 ViewsLast post 6/28/19, 10:45 PM by William Duffield -
by Bill Tindall, E.TN. 6/23/19, 1:42 PM
28 Replies · 75 ViewsLast post 6/28/19, 6:37 PM by david weaver -
by John W Foster 6/28/19, 1:18 PM
1 Reply · 34 ViewsLast post 6/28/19, 3:17 PM by david weaver -
Question about Exterior Painting job
by Alan Young 6/27/19, 2:22 PM
4 Replies · 38 ViewsLast post 6/27/19, 7:32 PM by Barry Irby -
Wrench size for collet on Festool Router???
by Barry Irby 6/25/19, 11:17 PM
8 Replies · 46 ViewsLast post 6/27/19, 5:56 PM by Bill Howatt -
what's with all the Windows updates
by Bill Tindall, E.TN. 6/27/19, 12:44 AM
6 Replies · 32 ViewsLast post 6/27/19, 2:50 PM by david weaver -
recommendations for drill bits
by Michael van pelt 6/22/19, 3:12 AM
14 Replies · 37 ViewsLast post 6/25/19, 7:36 PM by Johanna