General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
Quartersawn White Oak - Grain Direction
by Chuck Steger 10/10/07, 3:03 PM
5 Replies · 43 ViewsLast post 10/11/07, 2:18 PM by John Cotten -
by Virgil Johnson 10/9/07, 11:48 PM
10 Replies · 36 ViewsLast post 10/11/07, 12:21 AM by Dominic Greco in Richboro PA -
by JL 10/8/07, 3:25 PM
13 Replies · 132 ViewsLast post 10/10/07, 11:23 PM by JL -
by Brian in Brighton 10/10/07, 10:39 PM
0 Replies · 27 ViewsLast post 10/10/07, 10:39 PM by Brian in Brighton -
by Barry Irby 10/9/07, 11:47 PM
9 Replies · 43 ViewsLast post 10/10/07, 10:29 PM by Lee Brubaker -
by CARL ALLEN 10/10/07, 8:18 PM
3 Replies · 31 ViewsLast post 10/10/07, 9:14 PM by CARL ALLEN -
by Doug Reynolds in Seattle 10/10/07, 8:36 PM
1 Reply · 33 ViewsLast post 10/10/07, 9:00 PM by Ron Hildreth, Alta, Iowa -
What is your favorite pocket knife? 2
by Pat Riley in SLC 9/28/07, 4:38 AM
49 Replies · 126 ViewsLast post 10/10/07, 7:44 PM by Mark Mandell - Gone Round In Jersey -
by Barry Irby 10/9/07, 8:02 PM
4 Replies · 43 ViewsLast post 10/10/07, 6:30 PM by Doug Turner -
by Sean Troy 10/10/07, 5:59 PM
0 Replies · 34 ViewsLast post 10/10/07, 5:59 PM by Sean Troy -
Tormek question - that angle setting jig
by Mike Schwing from Md. 10/10/07, 10:55 AM
4 Replies · 42 ViewsLast post 10/10/07, 4:15 PM by JohnKJordan in East TN -
by Hamish 10/10/07, 8:01 AM
2 Replies · 40 ViewsLast post 10/10/07, 4:13 PM by Lee Schierer - McKean, PA -
New Yankee videos for download *LINK*
by Dan Mitchell 10/9/07, 11:46 PM
13 Replies · 82 ViewsLast post 10/10/07, 4:01 PM by Garrett in Victoria -
by Dean Lapinel 10/9/07, 5:19 AM
2 Replies · 28 ViewsLast post 10/10/07, 3:59 PM by Dean Lapinel -
Is it possible to make this with a router?
by lee beeden 10/8/07, 4:32 PM
16 Replies · 92 ViewsLast post 10/10/07, 3:48 PM by Barry Irby -
by JTSmithers 10/10/07, 3:35 PM
0 Replies · 25 ViewsLast post 10/10/07, 3:35 PM by JTSmithers -
by Dave W 10/9/07, 8:36 PM
3 Replies · 81 ViewsLast post 10/10/07, 2:38 PM by Dave W -
by Tom Norton 10/7/07, 11:49 AM
27 Replies · 127 ViewsLast post 10/10/07, 2:12 PM by Larry Clinton -
by John McGaw 10/9/07, 10:24 PM
3 Replies · 60 ViewsLast post 10/10/07, 1:17 PM by Mark Mandell - Gone Round In Jersey -
Source for high-pressure laminate??
by Pieter B. Ruiter 10/9/07, 8:41 PM
8 Replies · 44 ViewsLast post 10/10/07, 1:02 PM by Jim Dillon -
by Jim DeLaney, Austintown, Ohio 9/21/07, 11:38 AM
8 Replies · 48 ViewsLast post 10/10/07, 12:29 PM by Larry Clinton -
by Mark Goodall - ATL - tooljunkie 10/9/07, 11:35 AM
10 Replies · 48 ViewsLast post 10/10/07, 12:06 PM by Barry Irby -
Drilling End Holes for Shutter Louvers
by Steve Lillie 10/9/07, 5:47 PM
4 Replies · 46 ViewsLast post 10/10/07, 11:13 AM by Steve Lillie -
by Bill Hammond, Oregon Coast 10/9/07, 8:30 PM
2 Replies · 29 ViewsLast post 10/10/07, 4:21 AM by Stuart Hough -
by Ray Thompson - Middletown,IN 10/10/07, 1:51 AM
0 Replies · 32 ViewsLast post 10/10/07, 1:51 AM by Ray Thompson - Middletown,IN -
by Dave Winters 10/9/07, 10:58 PM
2 Replies · 25 ViewsLast post 10/10/07, 12:37 AM by Robin Corell in Atascadero Ca -
by Tom Norton 10/8/07, 11:09 PM
8 Replies · 41 ViewsLast post 10/9/07, 11:18 PM by Paul Waddle -
Any tips on working with Formica? *LINK*
by Dan Mitchell 10/8/07, 11:24 PM
15 Replies · 58 ViewsLast post 10/9/07, 11:14 PM by Dan Mitchell -
by dalegolf 10/8/07, 3:56 AM
15 Replies · 51 ViewsLast post 10/9/07, 8:33 PM by Scott Greaves in Blackfoot Idaho -
by David Yoho 10/8/07, 11:04 PM
8 Replies · 33 ViewsLast post 10/9/07, 7:46 PM by kees



