Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Question on resawing?

Posts

Question on resawing?

#1

Question on resawing?

Barry Irby

>I have mentioned many times that I have a love hate relationship with my bandsaw. I would love for it to work some magic for me, but I think we hate each other.

I just resawed two walnut boards 6 1/2" by 48". I was trying for pieces about an 1/8" thick. I used a homemade single point fence and drew a line done the edge. I ruined one cut and then switched to a new blade. Much better. After sanding away the saw marks, I ended up with a stack of pieces that added up to almost exactly one of the pieces I started with. I have seven pieces. I would have had eight if I had not blown the first cut. Is that pretty good? Nearly a fifty percent loss? Wonder if it is time to try a Wood Slicer or something fancier than the half inch 3 tpi blade I used?

Re: Question on resawing?

#2

Re: Question on resawing?

Garrett in Victoria

>Hi Barry

With a perfectly tuned saw and lot of luck, you might have got 3 1/8 slats out of a 3/4" board.

Think about what's required. If/if you are able to saw an almost perfect vertical line from either face, you can produce 3 slats roughly 3/16" thick, but inevitably, just a little thicker or thinner in several places. Now you have to plane the two outside slats and both joint and plane the middle slat which is rough on both faces. Voila, three perfect 1/8" slats.

But, how likely is this outcome? A little band wander, a bit of inattention keeping the board perfectly vertical all the way through, a jerky push... In an instant, you're lucky to get two slats.

You and your saw didn't do too badly when all's said and done.

Cheers, Garrett

Re: Question on resawing?

#3

Re: Question on resawing?

Larry Clinton

>Barry, don't know what blade your currently using - but I was amazed at the difference the Timberwolf made the first time I used one. Then I bought a Woodslicer from Highland Hardware. It is even better that the Timberwolf in my opinion. In my opinion, I got just about as much benefit from the better blades as I did from the several hours of tuning my old saw. I now have a MM 16 and the results using a top blade on a top quality saw are unbelievable to me. A second benefit of buying my MiniMax - SHMBO thought it was a good buy, she thinks it is pretty!

Re: Question on resawing?

#4

Hmmm? Bandsaw as a Chick magnet? NOT!

Barry Irby

>I'm single.

I think I will try one of the blades. I have been trying to use one blade for everything. Its a half inch 3tpi blade that the guy that did the article on tuning the bandsaw In FWW used.

Can you resaw a six inch wide board with a regular fence or do you still have to use a single point fence and carefully guide it through?

Re: Question on resawing?

#5

Re: Hmmm? Bandsaw as a Chick magnet? NOT!

Dennis Yoder

>I use the Suffock blades and adjust the flat fence to compinsate for the drift. Dennis Y

Re: Question on resawing?

#6

depends on the saw

Robin Corell, in Atascadero CA

>Kind of depends on your saw and how it is tuned. My old saw, a mid 1920's 16" didn't have crowned tires and I could only resaw with a single point fence. rather than hassle with the tires I ended up finding a great deal on an old Craftsma/Parks 18" saw. after tuning it up I have found that I can use a full height fence when resawing thin stock with fantastic results. Up until now I have never seen a reason to look into an expensive blade and have always used a 1/2" 3 tooth as well. I didn't see how a better blade would make much difference due to the blade wander. On my 18" saw and a full fence I can see where the better blades would add to the smoothnes of the cut and consequently allow for less ssnding and more slices out of a board.

Robin

Re: Question on resawing?

#7

Re: Hmmm? Bandsaw as a Chick magnet? NOT!

Larry Clinton

>I tried slicing a piece of 14" ~ 16" long X about 8" or 9" white oak about 1/16 thick with my MM 16 using the straight fence that came with the saw and a 1/2" woodslicer blade. I did square up the board using my planer and jointer. Without adjusting the fence for runout, the piece came out with a little less than .010 variation in thickness (I think most of the variation was due to "tilting" the board due to the low fence). I am sure most of the error was due to the low fence. I'm sure I could be more accurate by attaching a high fence to the existing about 3" - 4" fence". Then fine tuning the fence for any lead angle required. I am equally sure I don't need to use a "point" fence.

Re: Question on resawing?

#8

Re: Hmmm? Bandsaw as a Chick magnet? NOT!

Larry Clinton

>I tried slicing a piece of 14" ~ 16" long X about 8" or 9" white oak about 1/16 thick with my MM 16, using the straight fence that came with the saw and a 1/2" woodslicer blade. I did square up the board using my planer and jointer. Without adjusting the fence for runout, the piece came out with a little less than .010 variation in thickness. I think most of the variation was due to "tilting" the board due to the low fence. I'm sure I could be more accurate by attaching a high fence to the existing about 3" - 4" fence". Then fine tuning the fence for any lead angle required. I am equally sure I don't need to use a "point" fence.

Re: Question on resawing?

#9

Anybody tried these yet? *LINK*

Curt Harms

>I saw these posted somewhere, don't remember where. They look interesting, the woodsaver plus claims a .030 kerf. Carbide impregnated? Snake oil?


Supercut Bandsaw Blades

Re: Question on resawing?

#10

Re: Hmmm? Bandsaw as a Chick magnet? NOT!

Lee Brubaker

>Hi Larry:

Suggestion.....don't use your resaw blade for anything other than resawing. A resaw blade is not a general purpose blade. In fact, do not hang your resaw blade on a peg on the wall when not in use. That is as bad as sawing curves. Recoil the blade & reattach it to the cardboard backing that it came with...then hang it on the wall.

Lee