Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

What size breaker?

Posts

Re: What size breaker?

#26

Re: I may be one....

Mark Goodall - ATL - tooljunkie

>Ooops... hit the wrong key.....

You assume correctly. The breaker box was full, the walls were full, and there was no place to put another outlet box. The only option was to replace the 3' of wire and put in new wire, new box, etc. My garage workshop is cramped to say the least, both electrically, floor space and wall space.

Neighbors who have the same size garage (2-car) laugh at how cramped everything is in my shop, cause all they have in theirs is a car or two and perhaps a few shelves to hold a few things. But when I see other garage workshops of peers here, I'm relieved to know that I'm not the only one cramping too much into a small workshop.

I certainly didn't think that I'd ever need a 30A circuit when I got the Unisaw. And since I see myself as fairly average I think there ought to be quiet a few more people like me who would benefit from putting in a 30A circuit instead of a 20A circuit if they can only have one for their cramped garage workshop.

So I think I'll continue giving my advice, making sure that it's clear that the 30A is not because the 3HP Unisaw needs it, it's to give you a little room to grow.

Happy Woodworking!

Re: What size breaker?

#27

Re: I wouldn't

tim_in_michigan

>I'm not argueing with you. I figured it probably wouldn't be approved, I know it wouldn't be the right way to do it. I've only got one short 220v run. Previously I only had one 220v tool. Now I've got 3 and need to add some more plugs. Running them off that one outlet with a extension cord is getting annoying. So I'm thinking about pulling the one 20amp run I've got and adding a couple 30 amp runs. I don't need the 30 amps but since I've already got a box of 30 amp receptacles and 30 amp cord plugs I'm thinking of making everything consistant and I think the wire will cost me less than buying plugs and outlets.

So would it be code approved for me to change the end on the tools cord to a 30 amp plug or am I not supposed to plug a tool only needing 20 amps into a 30 amp circuit?

Re: What size breaker?

#28

Re: I wouldn't

Larry Clinton

>Tool amperage draw, other than having to plug into a circuit that will provide the minimum necessary to start and run the tool is not revel ant to the breaker size. You plug in an electric razor pulling maybe 1 or 2 amp into the same outlet you use for your 12 - 15 amp hairdryer, don't you? You can legally plug in a 15 amp saw into a 30 amp breaker circuit. The breakers are designed and rated to protect the PERMANENT wiring only. I am not sure if your original idea meets code, but it would not be unsafe - (If I did it, I would change the receptacle before selling the house though to prevent someone thinking they have a larger circuit than they do). There is nothing wrong with your thinking. I did work within the code whenever possible. However NEC does not really cover all eventualities, sometimes you just have to use your head. As an example I have partially rewired (installed a new entrance and added outlets) many older 2 and three story homes with knob and tube wiring. Most have all lighting in the center of the ceilings. In many cases these wires cannot be replaced without removing the ceiling or floor above. The options are to connect the knob and tube to new romax wire or to refuse the job, as few or none of the owners would accept the cost or mess involved in tearing out and replacing all the ceilings in their home. To the best of my knowledge these connections are not addressed/allowed by the NEC. I feel I left these homes in far safer condition than when I started. I was taught wiring by my cousin (A lineman, later head of the transformer shop for Northern Indiana Public service company) and a family friend that initially wired many homes in the early 1900's. I completed a Coyne school electrical/electronic course in my teens. I actually have been wiring for more than 50 years and to the best of my knowledge have never had a fire start or anyone shocked / harmed by any of my wiring.