General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
grizzly shaper spindles and delta shapers
by tim_in_michigan 10/18/07, 3:17 AM
0 Replies · 47 ViewsLast post 10/18/07, 3:17 AM by tim_in_michigan -
by David Haywood 10/15/07, 1:34 AM
2 Replies · 57 ViewsLast post 10/18/07, 3:10 AM by Lee Brubaker -
by JohnKJordan in East TN 10/8/07, 5:02 PM
18 Replies · 43 ViewsLast post 10/18/07, 12:51 AM by Keith Newton -
looking for plans for a clothing Armoire
by Wayne 10/17/07, 3:11 AM
7 Replies · 52 ViewsLast post 10/18/07, 12:29 AM by DizD -
PVC for compressed air line runs.!?
by Ray Carson, Lawrenceville NJ 10/16/07, 5:48 PM
12 Replies · 59 ViewsLast post 10/17/07, 11:37 PM by Mark Mandell - Gone Round In Jersey -
by Ron Hildreth, Alta, Iowa 10/16/07, 8:21 PM
9 Replies · 62 ViewsLast post 10/17/07, 10:29 PM by Glenn Madsen near San Francisco -
Way O.T: Hot tub heater wiring question
by David Sparks 10/17/07, 4:29 PM
4 Replies · 51 ViewsLast post 10/17/07, 10:22 PM by David Sparks -
by Scott Greaves in Blackfoot Idaho 10/16/07, 7:24 PM
5 Replies · 42 ViewsLast post 10/17/07, 6:57 PM by Scott Greaves in Blackfoot Idaho -
by Max 10/15/07, 6:16 PM
21 Replies · 58 ViewsLast post 10/17/07, 4:39 PM by Mark Goodall - ATL - tooljunkie -
Need beam suggestions for bridge
by Phil Joines Krum, Tx 10/15/07, 10:25 PM
12 Replies · 58 ViewsLast post 10/17/07, 1:55 PM by Phil Joines Krum, Tx -
by Ernie Miller 10/16/07, 1:46 PM
9 Replies · 42 ViewsLast post 10/17/07, 1:30 PM by Jim Dillon -
by doug f 10/16/07, 5:55 PM
15 Replies · 46 ViewsLast post 10/17/07, 1:28 PM by Joe Pack -
by Mike Schwing from Maryland 10/16/07, 5:59 PM
12 Replies · 53 ViewsLast post 10/17/07, 11:28 AM by Mark Mandell - Gone Round In Jersey -
by Paul Waddle 10/13/07, 1:42 PM
3 Replies · 38 ViewsLast post 10/17/07, 3:32 AM by Doug Turner -
by Howard 10/15/07, 2:09 AM
3 Replies · 70 ViewsLast post 10/17/07, 3:29 AM by Doug Turner -
by David Yoho 10/16/07, 5:31 PM
2 Replies · 34 ViewsLast post 10/17/07, 1:29 AM by Dave Arbuckle -
WC Weekend Accomplishments.....
by Dennis E. Peacock 10/15/07, 2:11 PM
11 Replies · 55 ViewsLast post 10/16/07, 10:59 PM by Terry Quiram -
by JL 10/16/07, 1:50 PM
6 Replies · 49 ViewsLast post 10/16/07, 7:47 PM by Mark Mandell - Gone Round In Jersey -
by Paul Waddle 10/16/07, 1:12 PM
4 Replies · 27 ViewsLast post 10/16/07, 7:18 PM by Paul Waddle -
by teflon_jones 10/16/07, 2:59 AM
5 Replies · 78 ViewsLast post 10/16/07, 5:31 PM by Dave Bair - Eaton Rapids -
OT: Boat Cover and Storage Recommendations
by Bill Schreiber, Litchfield, NH 10/15/07, 12:55 PM
9 Replies · 41 ViewsLast post 10/16/07, 2:29 PM by Rob Stokes in North Vancouver -
by Chet Kloss 10/16/07, 12:54 AM
4 Replies · 36 ViewsLast post 10/16/07, 11:24 AM by Chet Kloss -
by Stephen Shepherd in the State of Deseret 10/16/07, 11:17 AM
0 Replies · 27 ViewsLast post 10/16/07, 11:17 AM by Stephen Shepherd in the State of Deseret -
Oak church pew lumber on classifieds
by Joe Pack 10/15/07, 3:10 AM
4 Replies · 30 ViewsLast post 10/16/07, 4:26 AM by Dave Peebles Lyons, Ohio! -
by William Christian 10/15/07, 5:32 PM
3 Replies · 28 ViewsLast post 10/16/07, 4:02 AM by DB -
bridgewood 12 inch jointer manual
by Joe Clark 10/16/07, 1:04 AM
1 Reply · 30 ViewsLast post 10/16/07, 1:29 AM by Steve Kirincich -
by Paul Waddle 10/11/07, 9:45 PM
13 Replies · 58 ViewsLast post 10/16/07, 12:59 AM by Keith Newton -
by DB 10/15/07, 4:03 AM
5 Replies · 31 ViewsLast post 10/15/07, 11:15 PM by Stuart Hough -
by Denis Ch�nard, Orl�ans, Ont. 10/14/07, 4:47 AM
6 Replies · 46 ViewsLast post 10/15/07, 10:10 PM by Jim Dillon -
Nitrocellulose lacquer alternative
by Roger 10/13/07, 8:28 PM
12 Replies · 1,596 ViewsLast post 10/15/07, 10:04 PM by Michael Dresdner



