Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Pecky?

Posts

Pecky?

#1

Pecky?

Scott Greaves in Blackfoot Idaho

>A while back I was talking to the guy at the local mill. They had bought a stand of dead timber, and were cutting it up, and found it was shot through with worm holes. He called it wormy fir. It has very nice grain and the holes are generally quite attractive. I bought a couple of bundles of this stuff.

I have unbanded one bundle of the wood, and run it through the planer, and have a nice consistent thickness on it now. I have not seen any evidence of remaining bugs, but I would be a fool to assume that it is bug-free. I haven't let any of it in my shop yet (did the planing in the back yard when the weather was nice!). I figure the best way to assure that it is bug-free is to have it kilned at a temperature that will kill any bugs, but I don't have a kiln.

Is there a possibility that I could use some kind of insecticide on the wood that would be effective? Is there any other way to kill off any remaining bugs? I don't want this stuff in my shop, much less in my house as a piece of furniture, if bugs are going to start dropping out of it next spring!!!

Thanks in advance!

Scott.

Re: Pecky?

#2

Cheeeep Bug Kiln

Mark Mandell - Gone Round In Jersey

>Get some heavy black plastic and wrap and tape seal the boards in bundles with a few spacers in between the boards. Place the bundles such that they will get full sunlight. You can even put a meat thermometer in to check. If you can get to and hold 180* on a couple of successive days, your bugs, if any, are toasty.

[and dead] |;-}

Been there, done that

Re: Pecky?

#3

the follow has worked for me

Bill Tindall, E.TN

>Spray it with something like malathion.

Spray it to wet it with most any solvent, eg lacquer solvent.

Put it in a bag and add moth balls.

Worms typically invade and leave permanently. Not likely that bugs remain.

Re: Pecky?

#4

I did this experiment this summer.......

Scott in Eastern Iowa

>.....with a load of auction bought red oak that was infested with PPB's.

I left the bundle wrapped in 6 mil black visqueen for at least 60 days and checked it at one point in mid august and got 128 degrees.

Dr Wengert over to Woodweb recommends 130 degrees to be sure.

My understanding is that anything sprayed on the surface will get the bugs trying to get in, but will not get the ones trying to get out. Theres simply not enough penetration for anything to work. There could be a chance that once they eat into the top layer coming out they might ingest enough to kill them, but at this point the jury is still out as to whether it worked or not.

That said, there is a new technique that I read about involving dry ice to quick freeze them. This option I have not tried yet....

Re: Pecky?

#5

Re: the follow has worked for me

Dick Coers

>Bill, Aren't you a little worried about malathion laced sanding dust when you work the wood?

Re: Pecky?

#6

Thanks Everybody!

Scott Greaves in Blackfoot Idaho

>The cheap kiln sounds like the way to go, although it may have to wait for next summer. Our high temps are already down in the 60's now, and we've had snow twice! Maybe I could just wait a month or two and try the freezing option! ;-)

Malathion was what I was thinking about spraying on it. I may still try some of that, and the solvent. Like I said, I really haven't seen current evidence of worms, I'd just rather take precautions than be sorry later.

This really is some beautiful wood - I hope I can save it!

Thanks!

Scott.