General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
Finishing Questions / Discussion
by Joanne Adler in Pt. Pleasant, PA 1/6/08, 2:59 PM
17 Replies · 62 ViewsLast post 1/8/08, 3:45 AM by Geary from NJ -
Any Leigh Superjig users out there?
by DizD 1/7/08, 3:06 AM
5 Replies · 57 ViewsLast post 1/8/08, 3:03 AM by DizD -
WC Weekend Accomplishments.....
by Dennis E. Peacock 1/7/08, 3:12 PM
11 Replies · 44 ViewsLast post 1/8/08, 2:41 AM by John Veerkamp -
by steve mackay 1/8/08, 1:19 AM
1 Reply · 19 ViewsLast post 1/8/08, 2:15 AM by Bill Roland (Mt Juliet,TN) -
by EmtFFKev 1/6/08, 5:50 AM
13 Replies · 166 ViewsLast post 1/8/08, 1:31 AM by EmtFFKev -
New tidbit on tankless Water Heaters (OT)
by Barry Irby 1/5/08, 8:21 PM
18 Replies · 103 ViewsLast post 1/8/08, 1:31 AM by Kevin Rabenaldt -
Reading Your Boards-Mark of Zoro?
by Bill Tindall, E.TN. 1/8/08, 1:05 AM
0 Replies · 52 ViewsLast post 1/8/08, 1:05 AM by Bill Tindall, E.TN -
by Dick Hines 1/7/08, 5:58 PM
1 Reply · 26 ViewsLast post 1/7/08, 8:10 PM by Barry Irby -
by Jim Shaver Oakville, Ontario 1/5/08, 11:45 PM
10 Replies · 32 ViewsLast post 1/7/08, 7:33 PM by Rob Lee -
by Joe 1/7/08, 6:47 PM
1 Reply · 23 ViewsLast post 1/7/08, 7:25 PM by Grant in Iowa -
by McKay 1/6/08, 3:37 AM
3 Replies · 52 ViewsLast post 1/7/08, 5:10 PM by Lee Schierer - McKean, PA -
by Wayne 1/6/08, 10:49 PM
13 Replies · 49 ViewsLast post 1/7/08, 4:30 PM by Art Silva -
by Bob in NE Ohio 1/6/08, 10:50 PM
6 Replies · 43 ViewsLast post 1/7/08, 3:53 PM by John in IN -
by Dan Donaldson 1/6/08, 4:00 AM
16 Replies · 48 ViewsLast post 1/7/08, 2:27 PM by Don Orr -
Porter Cable 4210 dovetail jig
by Dan Mitchell 1/5/08, 2:22 AM
9 Replies · 158 ViewsLast post 1/7/08, 5:31 AM by Dan Mitchell -
by Wayne 1/7/08, 2:27 AM
1 Reply · 26 ViewsLast post 1/7/08, 3:32 AM by Dustmaker Mike -
by Ken Kimura 1/5/08, 5:24 PM
7 Replies · 42 ViewsLast post 1/7/08, 3:12 AM by bob marino -
by DocJim...Fayetteville, NY 1/7/08, 3:10 AM
0 Replies · 24 ViewsLast post 1/7/08, 3:10 AM by DocJim...Fayetteville, NY -
by McKay 1/6/08, 3:34 AM
3 Replies · 31 ViewsLast post 1/7/08, 12:51 AM by Stuart Hough -
by Barry Irby 1/5/08, 1:10 PM
10 Replies · 32 ViewsLast post 1/6/08, 11:16 PM by Carol - now in NC Nebraska -
by Larry in NW Ohio 1/5/08, 1:50 PM
7 Replies · 44 ViewsLast post 1/6/08, 4:34 PM by Barry Irby -
Saving money heating your House (or Shop) (OT)
by Barry Irby 1/5/08, 9:21 PM
2 Replies · 34 ViewsLast post 1/6/08, 1:57 PM by Barry Irby -
by Scott Burr in Ben Lomond CA 1/4/08, 7:06 PM
8 Replies · 38 ViewsLast post 1/6/08, 5:28 AM by Scott Burr in fridgid Ben Lomond, CA -
I almost couldn't help laughing.......
by Barry Irby 1/4/08, 8:57 PM
15 Replies · 61 ViewsLast post 1/6/08, 2:31 AM by Bill Hammond, Oregon Coast -
by David Sparks 1/3/08, 12:02 PM
29 Replies · 216 ViewsLast post 1/6/08, 1:06 AM by Kevin Rabenaldt -
by peter bunnett 1/4/08, 3:50 PM
11 Replies · 51 ViewsLast post 1/5/08, 10:35 PM by Mark Mandell - Gone Round In Jersey -
Disassembling oak cabinet doors
by Dan Mitchell 1/3/08, 8:31 PM
11 Replies · 61 ViewsLast post 1/5/08, 2:16 PM by John Cotten -
Sad Times for Hand Tool Forum?
by Barry Irby 1/4/08, 8:39 PM
12 Replies · 43 ViewsLast post 1/5/08, 12:39 PM by wilbur------WebKitFormBoundarytUGnIvx+VQRRDQk3 -
by Jennifer@Indy.USA 1/4/08, 12:30 AM
7 Replies · 53 ViewsLast post 1/5/08, 3:34 AM by Dave Dewees -
by Tomm 1/3/08, 11:07 PM
6 Replies · 38 ViewsLast post 1/5/08, 3:27 AM by Dave Dewees



