Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

building massive stair treads

Posts

building massive stair treads

#1

building massive stair treads

peter bunnett

>I am potentially building 35 floating stair treads for a steel frame. The treads are 3"by16"by60" of domestic hardwood. I haven't worked with this thick of material before and am wondering about the logistics and economy of time involved in laminating the thickness as well as the width.Thanks Peter unnett

Re: building massive stair treads

#2

JL

Re: building massive stair treads

JL

>Thick wood is often more expensive than thin wood. Probably because it takes longer (and is more complicated) to dry properly. As your stair treads are 3" x 16" x 60", you would probably have a hard time finding that many (35) large pieces of 3" thick lumber.

Can you laminate it out of 4/4 (1") thick stock - sure. It might take a gallon of glue, but you can do it. I would think about finding some nice top and bottom pieces of 4/4 that is 16" wide (or as wide as you can get them). If you can't get the width, I would laminate them out of wood that is less wide. I would stagger the joints - say 2 pieces of 8" for the top and bottom layers and 10" and 6" (or 3 pieces of 5 1/3") for the middle layer. It will take a lot of clamps for that width and length. If you have enough clamps for laminating 1 or 2 pieces, it would take several hours for the glue to set - and then you could glue the next one.

My $0.02.

Re: building massive stair treads

#3

Re: building massive stair treads

Mark Mandell - Gone Round In Jersey

>Peter,

12/4+ stock will cost you a pretty penny and may be hard to find depending on which species you choose and your location. You may be able to save yourself a considerable amount of money, and possibly increase the strength of the treads by building a core out of engineered material like high quality ply, LVL, etc. and then sheathing if it with your face wood of choice in say 3/4 thickness on top and nose + 1/4" stock on the other 4 non-wearing surfaces. If you plan to profile the nose, heavier stock can be used there and still maintain a large cost savings

You can also consider building your treads as torsion boxes to lighten up the structural load.

mm

Re: building massive stair treads

#4

Develop some muscles

Lee Schierer - McKean, PA

>DeBetter start the weight lifting program now.....Those treads are foing to weigh at least 75 pounds each when finished if they are made of red oak. 35 of them will weigh about 2600 pounds. Make sure your frame will hold that weight plus the weight of the likely users (several of them at the same time)

Lee

Re: building massive stair treads

#5

Re: building massive stair treads

Barry Irby

>Peter, 16" is awfully wide for stair treads. The usual run for treads is about 10" (9" to 11" =/-) You might start by asking if they really need 16"

I would look around for a manufacturer of laminated timbers or even log cabins. There may be somebody out there with beams you can buy and cut to size or glue up.

Re: building massive stair treads

#6

For reference only....

Nat Robison

>You might want to see if you can access "This Old House" from a few years ago where they did a similar staircase in the modern-type house in the Boston area. I want to say the treads were solid teak but they may have been glue-ups. Funny, I don't recall them putting a price tag on that portion of the job.

The treads were constructed by a pro millwork shop. They routed out recesses on the bottom for the steel plate.

Re: building massive stair treads

#7

Ellis Walentine

Need more info

Ellis Walentine

>Is the finish thickness actually 3"? What domestic hardwood might this be? Are these straight-across treads or shaped like segments of a pie?

You've had several suggestions about laminating and/or fabricating these big boys, but I am of the opinion that if you can find the heavy stock, you're better off working with the full thickness.

In all my years in the biz, I never found that the cost of materials came close to the cost of fabricating something.

Ellis Walentine, Host

Re: building massive stair treads

#8

Re: For reference only....

don central illinois

>If I remember correctly, they were reclaimed teak, and I don't remember that ever mentioned the cost, either.

Re: building massive stair treads

#9

Re: Need more info

Barry Irby

>Ellis is correct. Think about this. If you can find a suitable hardwood in pieces large enough, that's the way to go. If you paid "X" per board foot and for ordinary sized stock and an addition $3 per foot for the massive sized stock, the additional for the oversized stock would be about $75 to $100 a tread. Are you wiling to prepare and laminate all those pieces for that? And, there is a good chance you clients would prefer solid wood and that the difference between the two would be less than that.

Re: building massive stair treads

#10

Depends

Mark Mandell - Gone Round In Jersey

>On how you quote the job and/or on how the customer specs the deal. You give them the options after you line up and price the materials vs. fabrication labor cost. The job has to net a certain amount either way or it's not worth doing.

I'd still be concerned about the total weight and load involved with that mass of wood on a huge frame. Peter hasn't mentioned what the steel frame's load rating is, and 35 steps is the best part of a 3-story staircase. First thing I'd do is get written confirmation from the structural engineer that the frame will accept the full anticipated load of wood plus users. Customers often don't think about such things, and if the structure comes down, the lawsuit's going to be against the guy who put too much weight on it.

mm

Re: building massive stair treads

#11

Re: Depends

Barry Irby

>You are right. It would certainly be wise to be sure that the structure would support the weight and the weight of the Users and under a sort of worst case scenario. (all 120 of them jumping up and down.) This could be three residential flights of steps or about two commercial ones, but in either case it still smart to make sure you don't get killed in the collapse. (Literally or figuratively)

I did not meant to imply that this aspect of the job was not important. I was just agreeing with Ellis in the aspect of there is a difference in the amount of work between taking a bunch of small pieces and doing a lot of prep and glue up or under perfect world circumstances just trimming the ends and sanding them a bit. Better make sure they will pass through your planer and sander. I cannot plane something 16" wide in my lunch box planer and this job would kill myPerformax. So another thought is to consider if you even have or have access to the equipment to do the job. I woudln't do it because I cannot chew a bite that big.

Re: building massive stair treads

#12

Re: Whoops

Mark Mandell - Gone Round In Jersey

>Barry,

Didn't mean to criticize your or Ellis' post. ['specially Ellis' |;-}} ] Just reinforcing what was already mentioned (Lee?) about load calculations. We've had several deck and staircase collapses in my area while I've been here, and it seemed like they were the result of a DIYer or "minimal pro" who didn't really proceed properly. Lot of people got hurt, several died.

mm