General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
kitchen counter: wood/laminate interface
by les winter 8/15/08, 10:06 AM
3 Replies · 17 ViewsLast post 8/15/08, 11:43 PM by les winter -
Anyone have Peachtree pocket screw jig? *LINK*
by Dan Mitchell 8/15/08, 11:06 PM
0 Replies · 16 ViewsLast post 8/15/08, 11:06 PM by Dan Mitchell -
OT - Some people complain about squirrels..
by JL 8/14/08, 7:14 PM
9 Replies · 30 ViewsLast post 8/15/08, 9:08 PM by Mark Mandell - Gone Round In Jersey -
by Dave Winters 8/14/08, 10:58 PM
17 Replies · 37 ViewsLast post 8/15/08, 4:29 PM by Keith Newton, LR, Arkansas------WebKitFormBoundary -
by George 8/14/08, 12:45 AM
6 Replies · 20 ViewsLast post 8/15/08, 3:46 PM by Ken Oakley-Sunny St. Cloud, Fla -
by les winter 8/14/08, 11:27 AM
5 Replies · 19 ViewsLast post 8/15/08, 12:17 PM by Ellils Walentine -
by howard 8/12/08, 5:41 PM
5 Replies · 20 ViewsLast post 8/15/08, 11:55 AM by Barry Irby -
by Dwain - Lakeland FL 8/11/08, 5:50 PM
26 Replies · 71 ViewsLast post 8/15/08, 4:27 AM by jan derr -
?????????????????Alan in Little Washington (NC)
by Howard In Toronto 8/13/08, 4:01 PM
1 Reply · 18 ViewsLast post 8/15/08, 4:11 AM by Alan -
by Vincent Booth 8/8/08, 3:38 PM
8 Replies · 25 ViewsLast post 8/15/08, 3:28 AM by jan derr -
Raising a plunge router in a router table *LINK*
by Dan Mitchell 8/12/08, 11:03 AM
9 Replies · 23 ViewsLast post 8/15/08, 1:47 AM by Alan -
by Jim Shaver - Oakville, Ont 8/14/08, 12:06 PM
23 Replies · 73 ViewsLast post 8/15/08, 1:20 AM by Jim Shaver - Oakville, Ont -
Bar Mold Miter Angles for 90 & 120 degrees
by Scott Davies 8/13/08, 11:11 PM
1 Reply · 20 ViewsLast post 8/14/08, 11:15 PM by Rick Christopherson -
Too bad this kind of lumber deals doesn't *LINK*
by North of the Border 8/12/08, 2:12 PM
1 Reply · 10 ViewsLast post 8/14/08, 9:47 PM by steve kreitler -
by Dustmaker Mike 8/14/08, 9:29 PM
0 Replies · 18 ViewsLast post 8/14/08, 9:29 PM by Dustmaker Mike -
by steve mackay 8/14/08, 7:07 PM
1 Reply · 12 ViewsLast post 8/14/08, 8:43 PM by Justin Szeliga -
by Marv....... Northern California Lake Co. 8/13/08, 5:28 PM
32 Replies · 92 ViewsLast post 8/14/08, 6:18 PM by Dale Lenz -
Feeling somewhat overwhelmed by IWF...
by JL 8/13/08, 11:06 PM
5 Replies · 13 ViewsLast post 8/14/08, 2:04 PM by Dick Coers -
by Tom Dunlap 8/13/08, 8:15 PM
8 Replies · 56 ViewsLast post 8/14/08, 1:51 PM by Tom Dunlap -
Great interview with Leonard Lee *LINK*
by Charles R. Smith 8/11/08, 1:28 PM
3 Replies · 19 ViewsLast post 8/14/08, 1:41 PM by Mike Fitterling -
by Jim Shaver - Oakville, Ont 8/9/08, 12:35 AM
5 Replies · 18 ViewsLast post 8/14/08, 12:50 PM by Jim Shaver - Oakville, Ont -
Need yet another dovetail gadget? *LINK*
by Forrest Addy 8/10/08, 12:35 AM
11 Replies · 83 ViewsLast post 8/14/08, 11:01 AM by Charlie Self -
OT, Off the chart, Dirt Bike agility. *LINK*
by Keith Newton, LR, Arkansas------WebKitFormBoundary 8/13/08, 1:03 AM
12 Replies · 61 ViewsLast post 8/14/08, 10:50 AM by Charlie Self -
by Dustmaker Mike 8/12/08, 10:16 PM
7 Replies · 21 ViewsLast post 8/14/08, 4:22 AM by on Henthorn -
by Bill P 8/7/08, 11:07 PM
11 Replies · 42 ViewsLast post 8/14/08, 1:05 AM by charlie belden -
by Thomas S Stockton 8/13/08, 1:25 AM
14 Replies · 40 ViewsLast post 8/13/08, 8:05 PM by Jennifer@Indy.USA -
OT - Painting a steel garage door
by Tim Greif - West of Chicago 8/12/08, 1:36 PM
5 Replies · 23 ViewsLast post 8/13/08, 7:05 PM by Pete LaBelle -
Finishing face frames and carcass
by Bill H. 8/12/08, 5:55 PM
4 Replies · 38 ViewsLast post 8/13/08, 5:05 PM by Vincent Booth -
by Tom Rex 8/13/08, 2:45 AM
1 Reply · 19 ViewsLast post 8/13/08, 3:49 PM by Kris Lasure -
by Bill Howatt 8/12/08, 4:31 PM
7 Replies · 20 ViewsLast post 8/13/08, 2:22 PM by pecker



