General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
***SPECIAL GUEST CHAT - GARY ROGOWSKI*** *LINK*
by Ellis Walentine 11/13/12, 6:46 PM
0 Replies · 27 ViewsLast post 11/13/12, 6:46 PM by Ellis Walentine -
by JL 11/8/12, 10:29 AM
6 Replies · 61 ViewsLast post 11/13/12, 6:43 PM by Howard Acheson -
by tom 11/12/12, 9:02 PM
9 Replies · 18 ViewsLast post 11/13/12, 4:48 PM by tom -
Tuesday Night Hand Tool Chat - Measuring
by Stephen Shepherd 11/13/12, 3:05 PM
0 Replies · 19 ViewsLast post 11/13/12, 3:05 PM by Stephen Shepherd -
Another Arborescent Table in progress *LINK*
by Keith Newton 11/12/12, 6:24 PM
6 Replies · 37 ViewsLast post 11/13/12, 2:36 PM by Thomas Skaggs -
by Joe Vultaggio 11/12/12, 9:54 PM
3 Replies · 23 ViewsLast post 11/13/12, 1:02 AM by don stephan -
Craftsman Rips off Bionic Wrench *LINK*
by Thomas Skaggs 11/9/12, 9:27 PM
11 Replies · 43 ViewsLast post 11/12/12, 9:11 PM by Larry Clinton At Frankfort, (Central) Indiana -
by Gary Smyth 11/12/12, 4:19 PM
1 Reply · 20 ViewsLast post 11/12/12, 6:42 PM by John in NM -
by Matthew Bruns 11/12/12, 3:06 AM
2 Replies · 17 ViewsLast post 11/12/12, 6:16 PM by Hank Knight -
by Shelley Thomsen 10/31/12, 12:12 AM
10 Replies · 38 ViewsLast post 11/12/12, 1:37 PM by Shelley Thomsen -
Installing unfinished oak floor
by Lynn Reedy 11/11/12, 2:11 AM
12 Replies · 47 ViewsLast post 11/12/12, 12:29 PM by Barry Irby -
by eliot feldman 11/10/12, 10:30 PM
11 Replies · 60 ViewsLast post 11/12/12, 3:11 AM by Matthew Bruns -
by McKay 11/9/12, 4:54 PM
2 Replies · 18 ViewsLast post 11/12/12, 1:46 AM by Ron in Eugene -
home built CNC milling machine question
by Bill Tindall, E.TN. 11/11/12, 1:41 PM
2 Replies · 17 ViewsLast post 11/11/12, 7:31 PM by John in NM -
OT -- Ok, I learned... never buy a used HD
by John in NM 11/9/12, 9:55 PM
8 Replies · 18 ViewsLast post 11/10/12, 8:41 PM by Bill Howatt -
by McKay 11/9/12, 9:22 PM
4 Replies · 20 ViewsLast post 11/10/12, 7:36 PM by larry in nw ohio -
by Justin Szeliga 11/8/12, 8:54 PM
8 Replies · 26 ViewsLast post 11/9/12, 11:15 PM by Justin Szeliga -
by Jerry Gibbs 11/9/12, 2:16 PM
9 Replies · 45 ViewsLast post 11/9/12, 10:52 PM by Barry Irby -
Finishing the inside of garage?
by Charles Jackson III 11/9/12, 3:29 PM
9 Replies · 57 ViewsLast post 11/9/12, 8:55 PM by Charles Jackson III -
by Jerry Gibbs 11/8/12, 7:18 PM
4 Replies · 14 ViewsLast post 11/9/12, 1:16 PM by Tim Caley -
by eliot feldman 11/7/12, 3:07 PM
11 Replies · 42 ViewsLast post 11/8/12, 11:15 PM by eliot d -
OT Voice Activated GPS question
by Barry Irby 11/8/12, 12:07 PM
2 Replies · 17 ViewsLast post 11/8/12, 7:31 PM by Bill Houghton -
by JERRY DRAPER 11/5/12, 9:48 PM
18 Replies · 978 ViewsLast post 11/8/12, 11:35 AM by Barry Irby -
by Ed Dart 11/6/12, 7:06 PM
14 Replies · 23 ViewsLast post 11/8/12, 4:40 AM by Rick Snyder -
Any news on the Colonel's condition?
by Larry Clinton At Frankfort, (Central) Indiana 11/7/12, 11:15 PM
0 Replies · 17 ViewsLast post 11/7/12, 11:15 PM by Larry Clinton At Frankfort, (Central) Indiana -
by GregTapler 11/6/12, 8:12 PM
4 Replies · 14 ViewsLast post 11/7/12, 5:35 PM by GregTapler -
OT.....just voted, what a crowd !!.....
by roger lance 11/6/12, 5:17 PM
10 Replies · 40 ViewsLast post 11/7/12, 3:53 PM by Tom Pilsbury (Chicago) -
Sick Rockwell 6 x 18" 22-201 surface planer
by Pete in Holland, MI 11/6/12, 3:39 AM
4 Replies · 9 ViewsLast post 11/7/12, 1:12 PM by Rick L -
by Tom Dunlap 11/7/12, 2:56 AM
2 Replies · 12 ViewsLast post 11/7/12, 12:45 PM by Bob -
by larry in nw ohio 11/6/12, 3:51 PM
3 Replies · 26 ViewsLast post 11/7/12, 12:39 PM by larry in nw ohio



