Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

12" blade on a 10" saw?

Posts

12" blade on a 10" saw?

#1

12" blade on a 10" saw?

JERRY DRAPER

Just finished a TS dovetail sled intended for a large carcass. I forgot to take in to account the blade height of my 10" saw and the blade does not extend high enough above the tail ramps. Is there any reason why I cannot use a 12" blade on a 10" contractor's saw?

Re: 12" blade on a 10" saw?

#2

Re: 12" blade on a 10" saw?

Hoa in Alameda

I'll be surprised if you can even install the 12" blade.

Assuming you can install the blade and it can spin without hitting anything it's not designed to hit (i.e. the board being cut), the only concern I have is the speed at the rim of the blade. It's 20% higher than that of a 10" blade. You need to make sure the speed does not exceed manufacturer's recommendation.

Re: 12" blade on a 10" saw?

#3

JL

Re: 12" blade on a 10" saw?

JL

Well, I can think of several reasons.

Your insert plate usually won't let you extend the height that much. If you use a zero clearance insert, that might be better - but you REALLY have to watch the height.

The arbor size is often different between 12" and 10".

What Hoa said.

Re: 12" blade on a 10" saw?

#4

Re: 12" blade on a 10" saw?

JERRY DRAPER

Thanks for the info. - just what I needed to know.

Re: 12" blade on a 10" saw?

#5

Re: 12" blade on a 10" saw?

Ralph Lipeles

Yes, arbor size on 10" saw blades is 5/8". Arbor size on 12" saw blades is 1 1/4".

Ralph Lipeles

Re: 12" blade on a 10" saw?

#6

Good point . . .

steve mackay

never thought of that one. Blades ARE "engineered" with a lot of thought about deforming and expansion "at speed" aren't they ? Those cute little cut-outs and "let-ins" (what ever they're called) around the edges. Brings to mind the Mythbusters when they mounted a CD on a die grinder and the CDs "failed".

Re: 12" blade on a 10" saw?

#7

I don't understand the problem

Bill Tindall

What are "tail ramps"?

A 10" blade sticks up something on the order of 3" above the table. What are you sawing that requires a sled and that sort of blade height? Even if the sled is made from 3/4" stuff (mine is 1/2" and works well) I can't picture a cut requiring such a blade height.

Re: 12" blade on a 10" saw?

#8

Bob

Re: I don't understand the problem

Bob

My thoughts exactly

Re: 12" blade on a 10" saw?

#9

Re: I don't understand the problem

JERRY DRAPER

The sled is made to accommodate a 24" panel with 6:1 dovetails. The base is 1/2" thick and 48" long. The pins are cut on the front side of the sled and the tails on the back of the sled. The sled has one runner. The left side of the pins/tails are cut from one miter slot and the the sled is moved to the other miter slot to cut the other side. The tails are cut by holding the board on a ramp with a 6;1 slope that is glued to the base. The height of the base + the ramp at the saw kerf is 2 3/8" high. Thus, I cannot cut 3/4" dovetails. I would post a picture but I do not know how.

Re: 12" blade on a 10" saw?

#10

Ellis Walentine

FWIW

Ellis Walentine

You can get 12" blades with a 5/8" bore, and they will not run too fast on a 10" saw, but I doubt that the saw will allow you to install a larger blade. Usually tablesaw chasses are designed for the maximum blade size and will not have room for the larger blade. I wouldn't recommend trying it.

Ellis Walentine, Host

WoodCentral.com

Re: 12" blade on a 10" saw?

#11

question

Bill Tindall

I am not familiar with this means of cutting a dovetail. Personally I do them with a hand saw which is not difficult to learn to do. I gather the ramp somehow enables the angled cut to be made for a tail. Couldn't you tilt the blade to get the same effect?

Re: 12" blade on a 10" saw?

#12

Re: question

JERRY DRAPER

You can tilt the blade and achieve the same results but the teeth need to be ground to the proper angle - about 95 degrees.

Re: 12" blade on a 10" saw?

#13

Re: question

Keith Newton

i would like to hear more of your logic on how that is. I'm having trouble following you.

Re: 12" blade on a 10" saw?

#14

Re: question

Bob Entwisle in NJ

Just guessing here, but having a 10" blade reground for dovetails would probably be cheaper than a 12" blade, and a lot safer for a 10" saw.

Bob in NJ

Re: 12" blade on a 10" saw?

#15

Buy a Keller jig.....

Bill Tindall

.....or learn to cut them by hand. If you continue to build furniture you will eventually gravitate to hand cut dovetails so you might as well start now. A quality saw will help a lot. I suggest the Lee Valley as it is inexpensive and works as well as those costing twice as much. The Rob Cosman video, available from Lee Neilsen, will also be useful. I use it for teaching this topic.

Re: 12" blade on a 10" saw?

#16

Re: Buy a Keller jig.....

JERRY DRAPER

I do cut dovetails by hand - have many times. They are never perfect. I always have to repair small gaps. I have a Porter Cable jig. I do not like the 8:1 ratio on router bits. Using this sled I can use any ratio that I choose and obtain near perfect dovetails. BTY this jig was published in the August issue of "Woodworkers Journal" and there is a Youtube video of the jig. Google "Table Saw Dovetail Sleds".

Re: 12" blade on a 10" saw?

#18

Wow, that looks like the slowest.....

Dick Coers

way to cut dovetails EVER! And, you have to look around the board to cut to a line. What prevents you from miscutting on this since you have to cut to a line? I bet you still have to repair a gap or two. After all that, he still cleans it up with a chisel. Still a Keller for me thank-you very much.

Re: 12" blade on a 10" saw?

#19

I couldn't do that......

Barry Irby

I am a little dis-graphic or dyslexic or perhaps bass-ackwards and ADHD, and that method would drive me completely crazy. (a short trip on a good day)

I have to write on my pieces with chalk to keep them straight and I usually get at least one wrong anyway. (chalk is a great thing)

I could not get through even a single piece cutting lefts and rights and whatever. If I have do do multiple drawers that way, I would just shoot myself and get it over with.