Hand Tools
Traditional tools, sharpening, restoration, usage techniques.
Related: Hand Tools archive
Topic list
-
TopicStatisticsLast post
-
by Ernie Miller *Topeka 12/6/04, 12:06 AM
6 Replies · 17 ViewsLast post 12/7/04, 10:00 PM by Brad in Ottawa -
by Todd O. Cronkhite Maine Native in FL. Exile :~( 12/6/04, 8:21 PM
7 Replies · 17 ViewsLast post 12/7/04, 7:54 PM by Bob Hackett -
by Jim DeLaney, Austintown, Ohio 12/6/04, 12:00 AM
8 Replies · 43 ViewsLast post 12/7/04, 5:08 PM by Don Thompson - Cutler Ridge, Florida -
by John Longwitz-Doraville, GA 12/7/04, 4:28 AM
0 Replies · 30 ViewsLast post 12/7/04, 4:28 AM by John Longwitz-Doraville, GA -
by Jonathan Peck - N.Y. 12/3/04, 9:15 PM
15 Replies · 152 ViewsLast post 12/7/04, 4:25 AM by Bill Houghton -
by Pete 12/6/04, 7:17 PM
2 Replies · 83 ViewsLast post 12/7/04, 2:42 AM by Roger Bell, Oregon -
by Ernie Miller 12/2/04, 8:01 PM
5 Replies · 29 ViewsLast post 12/7/04, 2:15 AM by Jeff Schmidt (KY) -
by Moses Yoder in White Pigeon, MI 12/4/04, 1:01 PM
4 Replies · 21 ViewsLast post 12/6/04, 11:23 PM by Todd O. Cronkhite Maine Native in Florida Exile : -
by Moses Yoder in White Pigeon, MI 12/2/04, 9:09 PM
19 Replies · 31 ViewsLast post 12/6/04, 6:33 PM by Scott Burr in Ben Lomond CA -
LV MKII Sharpening System (QPSS)
by John Meikrantz 12/3/04, 3:15 PM
5 Replies · 31 ViewsLast post 12/6/04, 5:10 PM by John Todd -
by Charles McKinley 12/6/04, 4:10 PM
0 Replies · 53 ViewsLast post 12/6/04, 4:10 PM by Charles McKinley -
by David Miller 12/5/04, 2:29 PM
15 Replies · 22 ViewsLast post 12/6/04, 3:50 PM by Jorge Castaneda -
Planing a square edge (long). 2
by Paul Kierstead 12/2/04, 5:49 PM
33 Replies · 124 ViewsLast post 12/6/04, 12:52 PM by Adam Cherubini, NJ -
by Jorge Castaneda 12/5/04, 2:49 AM
9 Replies · 30 ViewsLast post 12/5/04, 3:28 PM by Jorge Castaneda -
okay, now this is funny (ebay) *LINK*
by Moses Yoder in White Pigeon, MI 12/3/04, 11:07 PM
9 Replies · 31 ViewsLast post 12/5/04, 1:26 PM by Todd O. Cronkhite Maine Native in FL. Exile :~( -
***SPECIAL GUEST CHAT: LON SCHLEINING!***
by Ellis Walentine 12/5/04, 12:21 PM
0 Replies · 60 ViewsLast post 12/5/04, 12:21 PM by Ellis Walentine -
help (of sorts) publ. of sheraton reprints
by Andrew F 12/5/04, 8:36 AM
0 Replies · 23 ViewsLast post 12/5/04, 8:36 AM by Andrew F -
new member in the plane family #9 *LINK*
by Rolf Schmid 12/4/04, 6:46 AM
4 Replies · 24 ViewsLast post 12/5/04, 8:03 AM by Rolf Schmid -
by Ernie Miller 12/3/04, 4:58 PM
15 Replies · 25 ViewsLast post 12/5/04, 4:36 AM by Bill Houghton -
by Bill Houghton 12/3/04, 2:10 AM
21 Replies · 29 ViewsLast post 12/5/04, 3:10 AM by Glenn Madsen -
by Howard Pollack 12/4/04, 12:07 AM
5 Replies · 30 ViewsLast post 12/4/04, 9:43 PM by Howard Pollack -
LN Small Low Angle Block Plane
by R.J.Whelan 12/2/04, 8:50 PM
11 Replies · 26 ViewsLast post 12/4/04, 7:16 AM by Dan Clermont in Burnaby -
by Ernie Miller *Topeka 12/3/04, 2:45 AM
3 Replies · 40 ViewsLast post 12/4/04, 3:04 AM by Kurt Loup -
Rehabed a couple of old chisels......
by Andy Halterman: Too much drivin' today 12/2/04, 3:54 AM
8 Replies · 31 ViewsLast post 12/3/04, 8:53 PM by Ted Shuck, Centennial, CO -
by Doug Reynolds in Seattle 12/3/04, 5:05 PM
1 Reply · 24 ViewsLast post 12/3/04, 8:21 PM by Bob Smalser, Seabeck, WA -
Need help making a molding with hand tools
by Wendell @ Murphy, TX 12/2/04, 4:21 AM
3 Replies · 20 ViewsLast post 12/3/04, 1:42 PM by Chad Boehlke -
by Peter Berglund in Denver 12/1/04, 5:45 PM
12 Replies · 59 ViewsLast post 12/3/04, 12:57 PM by Don Thompson - Cutler Ridge, Florida -
by Sam Simpson 12/2/04, 11:38 PM
0 Replies · 30 ViewsLast post 12/2/04, 11:38 PM by Sam Simpson -
Stanley #71: Made in USA or Eng., does it matter?
by Todd M 12/1/04, 11:24 PM
7 Replies · 89 ViewsLast post 12/2/04, 9:02 PM by John Horobin -
by matt 12/2/04, 12:18 AM
7 Replies · 44 ViewsLast post 12/2/04, 7:46 PM by Andrew F