General Woodworking
Cross-cutting topics, techniques, and questions that don’t fit a specialty.
Topic list
-
TopicStatisticsLast post
-
by Dustmaker Mike 2/12/09, 9:31 PM
14 Replies · 23 ViewsLast post 2/14/09, 2:31 AM by steve antonucci -
by Doug Reynolds in Seattle 2/11/09, 10:25 PM
4 Replies · 20 ViewsLast post 2/14/09, 1:09 AM by John K Jordan -
Piano Makers- What wood do they use?
by Alan Young 2/10/09, 11:21 PM
11 Replies · 51 ViewsLast post 2/14/09, 1:07 AM by John K Jordan -
I know I put my pencil someplace, but where?
by JL 2/13/09, 4:48 PM
8 Replies · 18 ViewsLast post 2/13/09, 11:59 PM by Glenn Madsen near San Francisco -
by Dan Donaldson 2/12/09, 4:34 AM
9 Replies · 18 ViewsLast post 2/13/09, 3:19 PM by Bill White -
by JL 2/12/09, 2:15 PM
8 Replies · 41 ViewsLast post 2/13/09, 3:18 PM by Bill White -
by Dave Tenney 2/12/09, 1:56 PM
5 Replies · 20 ViewsLast post 2/13/09, 1:52 PM by John K Jordan -
need start switch for DC motor
by Phil Joines in Krum, Tx 2/12/09, 4:25 AM
7 Replies · 20 ViewsLast post 2/13/09, 2:41 AM by wayne in Topanga -
Drum sander identification *LINK*
by Nathan 2/10/09, 2:06 PM
3 Replies · 20 ViewsLast post 2/12/09, 7:16 PM by Ellis Walentine, Host -
by jim short 2/11/09, 11:41 PM
7 Replies · 116 ViewsLast post 2/12/09, 7:09 PM by Ellis Walentine, Host -
by Howard Norman 2/10/09, 10:15 PM
11 Replies · 22 ViewsLast post 2/12/09, 4:55 PM by Ralph Turney in Huntington Beach, CA -
by Bob Fuller 2/11/09, 12:14 AM
7 Replies · 18 ViewsLast post 2/12/09, 4:10 PM by Frank Mutchler -
by John E in SC 2/12/09, 3:18 AM
6 Replies · 25 ViewsLast post 2/12/09, 3:09 PM by GalenV in Iowa -
by Stephen Shepherd in the State of Deseret 2/10/09, 12:55 PM
2 Replies · 14 ViewsLast post 2/12/09, 4:23 AM by Fred Davis -
OT - Bathtub walls alternatives
by Ralph Lipeles 2/10/09, 2:29 PM
11 Replies · 49 ViewsLast post 2/12/09, 4:16 AM by Fred Davis -
Aftermarket TS blade guard recommendations
by Jerry Samsen 2/10/09, 7:02 PM
17 Replies · 59 ViewsLast post 2/12/09, 3:00 AM by jsamsen -
Anybody know anything about GCB Imports? (OT?)
by Barry Irby 2/12/09, 12:36 AM
0 Replies · 13 ViewsLast post 2/12/09, 12:36 AM by Barry Irby -
Taking bets on when this guy loses a body part... *LINK* 2
by Dan Mitchell 2/6/09, 9:02 AM
32 Replies · 114 ViewsLast post 2/11/09, 8:17 PM by Fred Davis -
by Frederick harvie 2/11/09, 12:51 AM
11 Replies · 28 ViewsLast post 2/11/09, 8:00 PM by Fred Davis -
Dovetail Challenge for all *LINK*
by Chris Vesper 2/10/09, 10:52 PM
3 Replies · 9 ViewsLast post 2/11/09, 6:31 PM by Art Silva -
OT Ground Up/Down—Facts & Hogwash
by Rod Peterson -- Ormond Beach 2/10/09, 2:39 PM
21 Replies · 39 ViewsLast post 2/11/09, 2:17 PM by Ellis Walentine, Host -
finishing (or not) dry through tenons
by Phil in NJ 2/8/09, 10:09 PM
3 Replies · 16 ViewsLast post 2/11/09, 2:09 PM by Gary Evans Tallassee, TN -
Tis woodworker makes big wave in show *LINK*
by North of the Border 2/10/09, 6:47 PM
3 Replies · 23 ViewsLast post 2/11/09, 1:02 PM by John K Jordan -
Finally - Last kitchen question - cleaning wood
by Joe Pack 2/8/09, 4:57 AM
4 Replies · 25 ViewsLast post 2/11/09, 4:41 AM by Michael Dresdner -
by Fred Davis 12/28/08, 8:20 PM
25 Replies · 116 ViewsLast post 2/11/09, 3:34 AM by Fred Davis -
by Robert R. Clough - Thorncraft 2/10/09, 1:44 AM
6 Replies · 22 ViewsLast post 2/11/09, 2:29 AM by Robert R. Clough - Thorncraft -
If you had $100 How would you Spend it? (OT?)
by Barry Irby 2/4/09, 10:28 PM
20 Replies · 28 ViewsLast post 2/11/09, 1:35 AM by Keith Newton------WebKitFormBoundaryV6MZb+tiOpocz6 -
by Ned Bulken 2/9/09, 12:45 AM
7 Replies · 37 ViewsLast post 2/10/09, 11:08 PM by Eddie Pacheco; San Jose, Ca.-Now in Pitt. PA------ -
by Pat Evans 12/15/08, 12:09 AM
10 Replies · 23 ViewsLast post 2/10/09, 10:12 PM by Jerry Gibbs -
by Doug Ridley 2/9/09, 7:32 PM
4 Replies · 25 ViewsLast post 2/10/09, 7:54 PM by John Veerkamp



